Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Uživatelský manuál Strana 11

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 820
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 10
9/Series PAL Reference Manual
Index (General)
9/Series Grinder
Table of Contents
Operation andProgrammingManual
vii
12.9.7 Controlling Spindles (G12.1, G12.2, G12.3) 12-71..........................................
12.9.8 Spindle Orientation (M19, M19.2, M19.3) 12-72...........................................
12.9.9 Spindle Direction ( M03, M04, M05) 12-74................................................
12.9.10 Short Block Acc/Dec Check G36, G36.1 12-75...........................................
12.10 Dwell (G04) 12-78....................................................................
12.10.1 Dwell - Seconds 12-78............................................................
12.10.2 Dwell - Number of Spindle Revolutions 12-78............................................
12.11 Mirror Image (G50.1, G51.1) 12- 79........................................................
12.12 Axis Clamp 12-82....................................................................
12.13 Dual Axis Operation 12-82..............................................................
12.12.1 Parking a Dual Axis 12-84..........................................................
12.12.2 Homing a Dual Axis 12-85..........................................................
12.12.3 Programminga Dual Axis 12-86......................................................
12.12.4 Offset Management for a Dual Axis 12-88..............................................
Chapter 13
Wheel Length Offsets
13.0 Chapter Overview 13-1................................................................
13.1 T Words and Wheel Length Offsets 13-1....................................................
13.1.1 Selecting Wheel Length Of fsets (T Word) 13-2...........................................
13.1.2 Activation of Wheel Length Offsets 13-4................................................
13.2Programming Changes to Wheel Geometry and Radius Offset Tables (G10L10) 13-5...................
Chapter 14
Angled-Wheel Grinding
14.0 Chapter Overview 14-1................................................................
14.1 Angled-Wheel Grinder Configuration Assumptions 14-1.........................................
14.2 Determining the Wheel Angle 14-2........................................................
14.3 Angled-Wheel Mode (G15, G16.3 and G16.4) 14-4............................................
14.3.1 Normal Angled-Wheel Grinding Mode (G16.3) 14-6........................................
14.3.2 Two Step Angled-Wheel Grinding Mode (G16.4) 14-9......................................
14.3.3 Angled-Wheel Transform Off (G15) 14-11................................................
14.4 Position Displays for Angled-Wheel Grinders 14-12.............................................
14.5 Manual Motion on an Angled-Wheel Grinder 14-14.............................................
14.6 Homing an Angled-Wheel Grinder 14-15.....................................................
14.7 Plane Selection on Angled-Wheel Grinders 14-15..............................................
14.8 Offsets on an Angled-Wheel Grinder 14-16..................................................
14.9 Overtravels and Programmable Zones on an Angled-Wheel Grinder 14-17............................
Chapter 15
Dresser/Wheel Radius Compensation
15.0 Chapter Overview 15-1................................................................
15.1 Introduction to Dresser/Wheel Radius Compensation 15-2.......................................
15.2Programming Compensation (G40, G41, G42) 15-5...........................................
15.2.1 Application Schemes 15-5..........................................................
15.2.2 Compensation Block Format 15- 12....................................................
15.3 Generated Compensation Blocks G39, G39.1 15-15............................................
Zobrazit stránku 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 819 820

Komentáře k této Příručce

Žádné komentáře