Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt Uživatelský manuál stáhnout pdf (Strana 135)

Rockwell Automation Publication 750COM-UM001E-EN-P - October 2013 135

Adapter Parameters Appendix B

[Fr Peer Addr 1]

[Fr Peer Addr 2]

[Fr Peer Addr 3]

[Fr Peer Addr 4]

Sets the IP address bytes that specifies the device from which the

adapter receives (consumes) peer I/O data.

Important: The Fr Peer Addr must be on the same subnet as the

embedded EtherNet/IP adapter. See IP Addresses

on page 180 for

more information.

Changes to these parameters are ignored when Parameter 85 -

[Fr Peer Enable] is ‘1’ (On).

Default: 0

Minimum: 0

Maximum: 255

Type: Read/Write

Reset Required: No

85 [Fr Peer Enable]

Controls whether peer I/O input is operating. A value of ‘0’ (Off)

turns off peer I/O input. A value of ‘1’ (Cmd/Ref) overrides the

settings in Parameters 76 - [DLs Fr Peer Cfg], 78 - [Logic Src

Cfg], and 79 - [Ref Src Cfg] and automatically uses peer

Datalink 01 as the drive's present Logic Command and peer

Datalink 02 as the drive's Reference. A value of ‘2’ (Custom)

enables peer I/O input using the Datalink count and settings

provided by the user.

If the value of this parameter is changed from ‘1’ (Cmd/Ref) to ‘2’

(Custom) or from ‘2’ (Custom) to ‘1’ (Cmd/Ref) while peer

I/O is running, the drive will be commanded to do its Peer Fault

Action before the peer input mode is changed.

Default: 0 = Off

Values: 0 = Off

1 = Cmd/Ref

2 = Custom

Type: Read/Write

Reset Required: No

86 [Fr Peer Status]

Displays the status of the consumed peer I/O input connection.

Values: 0 = Off

1 = Waiting

2 = Running

3 = Faulted

Type: Read Only

87 [DLs To Peer Cfg]

Sets the number of drive-to-peer Datalinks (parameters) that are

used for peer I/O. The Datalinks being used are allocated from the

end of the list. For example, if this parameter's value is set to ‘3’,

Datalinks 14…16 are allocated for the 3 selected Datalinks. The

Datalinks allocated for this cannot overlap with other assigned

DL To Net 01-16 parameters.

NOTE: The adapter allows the peer output configuration

parameters to be written while peer outputs are running.

However, the changes will not take effect until peer outputs are

disabled and then re-enabled, or until the adapter is power

cycled or reset.

Default: 0

Minimum: 0

Maximum: 16

Type: Read/Write

Reset Required: Yes

88 [DLs To Peer Act]

Displays the value of Parameter 87 - [DLs To Peer Cfg] at the

time the drive was reset. This is the number of actual drive-to-

peer Datalinks that the drive is expecting.

Minimum: 0

Maximum: 16

Type: Read Only

89 [To Peer Period]

Sets the minimum time that an adapter will wait when

transmitting data to a peer.

Important: Changes to this parameter are ignored when

Parameter 91 - [To Peer Enable] is ‘1’ (On).

Default: 10.00 Seconds

Minimum: 0.01 Seconds

Maximum: 10.00 Seconds

Type: Read/Write

Reset Required: No

Parameter

No. Name and Description Details

255.255.255.255

[Peer Inp Addr 1]

[Peer Inp Addr 2]

[Peer Inp Addr 3]

[Peer Inp Addr 4]

1 2 ... 130 131 132 133 134 135 136 137 138 139 140 ... 189 190

Komentáře k této Příručce

Žádné komentáře

Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt Uživatelský manuál Strana 135

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt