Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN Uživatelský manuál Strana 116
- Strana / 172
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
116 Rockwell Automation Publication 520COM-UM003A-EN-E - June 2013
Chapter 8 Troubleshooting
PORT Status Indicator
This red/green bicolor LED indicates the status of the adapter’s connection to
the drive as shown in the table below.
MOD Status Indicator
This red/green bicolor LED indicates the status of the adapter as shown in the
table below.
NET A Status Indicator
This red/green bicolor LED indicates the status for the network connection as
shown in the table below.
Status Cause Corrective Actions
Off The adapter is not powered. • Securely connect the adapter to the drive.
• Apply power to the drive.
Flashing red The adapter is not receiving communication from the drive,
or a drive is missing in Multi-drive mode.
• Verify that cables are securely connected.
• Cycle power to the drive.
Flashing green The adapter is establishing communications with the drive. No action required. This status indicator will turn solid green or flashing red.
Steady green The adapter is properly connected and is communicating
with the drive.
No action required.
Orange The drive is not an Allen-Bradley drive, or the drive is
configured for Multi-drive mode using its embedded
EtherNet/IP port.
• Use an Allen-Bradley PowerFlex 520-Series drive.
• Set Host parameter C169 [MultiDrv Sel] to 1 “Network Opt” and cycle power to the drive.
Status Cause Corrective Actions
Off The adapter is not powered or is not properly connected to
the drive.
• Securely connect the adapter to the drive.
• Apply power to the drive.
Flashing red The cause may be one of the following:
• The drive is in firmware upgrade mode.
• The adapter has an EEPROM fault.
• The network address switches has been changed since
powerup.
• A duplicate IP address fault has been detected.
• The DHCP lease has expired.
• The network address switches are set to “888”.
• The network configuration (IP address, subnet mask,
gateway address) is invalid.
• The User FPGA configuration is invalid.
View the adapter event queue to determine which of these conditions is present. Then, depending on
the cause, take the appropriate corrective action.
• Clear faults in the adapter.
• Cycle power to the drive.
• If cycling power does not correct the problem, the adapter parameter settings may have been
corrupted. Reset defaults and reconfigure the adapter.
• If resetting defaults does not correct the problem, update the adapter with the latest firmware
revision.
• Change the network address switches to a value other than “888”.
Flashing green The adapter is operating normally, but is not transferring
I/O data to a controller.
• Place the scanner in RUN mode.
• Program the controller to recognize and transmit I/O to the adapter.
• Configure the adapter for the program in the controller.
• Normal behavior is no I/O is being transferred.
Steady green The adapter is operating normally and is transferring I/O
data to a controller.
No action required.
Status Cause Corrective Actions
Off The cause may be one of the following:
• The adapter is not powered.
• The adapter is not properly connected to the network.
• The adapter has not acquired its network configuration
(IP address, subnet mask, gateway address) from the
BOOTP server.
• Securely connect the adapter to the drive.
• Correctly connect the Ethernet cable to the Ethernet connector.
• Set a unique IP address with the adapter rotary switches, adapter parameters, or a BOOTP or DHCP
server.
• Apply power to the drive.
Flashing red The I/O connection has timed out. • Place the controller in RUN mode.
• Check the amount of traffic on the network.
Steady red The cause may be one of the following:
• A duplicate IP address fault has been detected.
• The DHCP lease has expired.
Configure the adapter to use a unique IP address and cycle power to the drive.
Flashing green The adapter is operating normally, but does not have any
CIP connections (I/O or explicit).
• Place the controller in RUN mode.
• Program the controller to recognize and transmit I/O, or make a message connection to the adapter.
• Configure the adapter for the program in the controller.
Steady green The adapter is operating normally and has at least one CIP
connection (I/O or explicit).
No action required.
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Overview 7
- Preface Overview 8
- Getting Started 9
- Features 10
- Understanding Parameter 10
- Compatible Products 11
- Required Equipment 11
- Safety Precautions 12
- Quick Start 13
- Chapter 1 Getting Started 14
- Installing the Adapter 15
- Setting the Node Address 16
- Connecting the Adapter to 18
- 00:00:BC:2E:69:F6 21
- Applying Power 22
- ENET LINK 23
- EtherNet/IP 23
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the PowerFlex 4-Class 27
- HIM to Access Parameters 27
- Setting the Adapter Node 27
- Using a BOOTP or DHCP 28
- Using Adapter Parameters 31
- Setting the Data Rate 32
- Using Master-Slave Hierarchy 33
- Setting a Fault Action 34
- Changing the Fault Action 35
- Resetting the Adapter 36
- Restoring Adapter 36
- Parameters to Factory 36
- Defaults 36
- Viewing the Adapter Status 37
- Using Parameters 37
- Updating the Adapter 37
- Firmware 37
- Configuring the I/O 39
- CompactLogix Example 40
- Configuring the I/O Chapter 4 41
- Designer 42
- Chapter 4 Configuring the I/O 46
- Controller Input Tags 47
- Controller Output Tags 47
- Logix Designer 50
- ADC and Logix Memory 54
- Monitoring the ADC Progress 55
- Input Image Controller Tags 60
- Output Image Controller Tags 60
- Limitations in Using 62
- MicroLogix 1100/1400 62
- Using the I/O 63
- Understanding the I/O Image 64
- Using Logic Command/Status 65
- Using Reference/Feedback 65
- Using Datalinks 66
- Example Ladder Logic 67
- Program Information 67
- Feedback 68
- Reference 69
- Logix Designer Software 70
- Chapter 5 Using the I/O 72
- Using Explicit Messaging 73
- Explicit Messaging Process 74
- Using Multi-Drive Mode 87
- System Wiring 89
- Configuring the RS-485 91
- Using Multi-Drive Add-On 91
- Differences Found Screen 101
- Multi-Drive Ladder Logic 102
- Program for Generic Profile 102
- CompactLogix Controller 103
- Example Using Generic 103
- Main Routine 104
- Drive 0...4 Control Routines 105
- Drive 0 Control Routine 106
- Drive 1 Control Routine 107
- Drive 2 Control Routine 108
- Drive 3 Control Routine 109
- Drive 4 Control Routine 110
- Multi-Drive Mode Explicit 111
- Messaging 111
- Additional Information 112
- Troubleshooting 115
- PORT Status Indicator 116
- MOD Status Indicator 116
- NET A Status Indicator 116
- NET B Status Indicator 117
- Viewing Adapter Diagnostic 117
- Viewing and Clearing Events 120
- Adapter Events 121
- Specifications 123
- Appendix A Specifications 124
- Adapter Parameters 125
- EtherNet/IP Objects 129
- Identity Object 130
- Instance Attributes 131
- Assembly Object 132
- Register Object 133
- Instances (Multi-Drive) 134
- Class Attributes 135
- Parameter Object 136
- PCCC Object 139
- N-Files 140
- DPI Device Object 142
- DPI Parameter Object 145
- on page 150 147
- Descriptor Attributes 148
- Formulas for Converting 150
- Common Services 150
- Object Specific Services 150
- DPI Fault Object 151
- TCP/IP Interface Object 153
- Ethernet Link Object 155
- Appendix D 157
- Logic Command Word 157
- Logic Status Word 158
- Position Bit Definitions 159
- Glossary 161
- Rockwell Automation Support 172
- Documentation Feedback 172
Související produkty a manuály pro Zařízení Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN
Zařízení Rockwell-automation 140MX-C_F Motor Protection Circuit Breaker Accesso Uživatelský manuál
(1 stránky)
(1 stránky)
Zařízení Rockwell-automation 194E Control and Load Switches 125...315 A, 3 Pole Uživatelský manuál
(1 stránky)
(1 stránky)
Zařízení Rockwell-automation 140U-xxx NFPA 79 Internal Rotary Operating Handle Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Uživatelský manuál
(8 stránky)
(8 stránky)
Zařízení Rockwell-automation 440T Single Key Slamlock with Electrical Isolation Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 440T Prosafe Dual Key Rotary Key Switches Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 440R Guardmaster Safety Relay GLP Installation Ins Uživatelský manuál
(4 stránky)
(4 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce