Rockwell-automation 1797-OE8H FLEX Ex HART Analog Modules User Manual Uživatelský manuál Strana 130
- Strana / 196
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Publication 1797-6.5.3 - March 2006
B-6 FLEX Ex HART Module Commands
Command 130
Channel 130, Read Instrument List From Index, indicates that the long frame
addresses of the transmitters were recognized on the current loops and
returned. A zero is returned if no device is detected.
The response of this command is also used to build a cross-reference between
I/O module’s loop number and the field device’s user ID. For example, use
this in the host software’s project tree. There are no request data bytes.
Table B.5 Command 130 Response Data Bytes
Byte Description Value
Response Data Bytes
0…4 EXT_ADDR_0 Extended address of instrument 0 —
5…9 EXT_ADDR_1 Extended address of instrument 1
… EXT_ADDR_I Extended address of the instrument
Command-specific Response Codes
5 Error Too few data bytes received
16 Error Access restricted
32 Error Busy
- FLEX Ex HART 1
- Analog Modules 1
- Important User Information 2
- Summary of Changes 3
- What’s Changed 3
- Summary of Changes 2 4
- Table of Contents 5
- Chapter 3 6
- How to Install Your FLEX Ex 6
- Table of Contents 3 7
- Table of Contents 4 8
- Table of Contents 5 9
- Table of Contents 6 10
- Table of Contents 7 11
- Table of Contents 8 12
- For Additional Information 14
- What This Chapter Contains 15
- What the FLEX Ex Analog 15
- I/O Modules Do 15
- How FLEX Ex Analog 16
- Modules Communicate 16
- Controllers 16
- Physical Features of Your 17
- Analog I/O Module 17
- Using Alarms on the 17
- 1797-IE8H Module 17
- Data Format Alarm Example 18
- Overrange Alarm 18
- Underrange Alarm 18
- Remote Fault Alarm 19
- Local Fault Alarm 20
- How to Use the 21
- HART Capabilities 21
- HART Implementation 21
- Overview 21
- HART Commands 22
- HART Target Tags 23
- HART Command Tags 24
- HART Initialize Tags 25
- HART Initialize Channel Tags 26
- Selecting the Correct Path 29
- Module Features 31
- Selecting a 1797-IE8H FLEX 32
- Ex Analog Input Module’s 32
- Operating Features 32
- High Low Error Level 33
- Input Filter Cutoff 33
- Data Format 34
- Data Formats and Error Ranges 36
- Selecting a 1797-OE8H FLEX 37
- Ex Analog Output Module’s 37
- Analog Digital State 38
- Analog Fault State Value 38
- Diagnostic Data error 40
- 11=data out of range 40
- Understanding Image Table 42
- Mapping and Bit/Word 42
- Descriptions 42
- 1797-IE8H and -OE8H 49
- Extended Configuration 49
- Data Table 49
- HART Status LEDs 50
- HART Status Inhibit 50
- 50/60 Hz Filter 50
- Before You Install Your 53
- Analog Module 53
- Compliance to European 54
- Union Directives 54
- Installation in Zone 1 55
- Installation in Zone 22 55
- Electrostatic Charge 55
- Removal and Insertion 56
- Under Power 56
- Install the Module 56
- Mount on a DIN Rail 57
- Panel/Wall Mount 59
- Label under here 61
- Wire the Terminal Base 62
- Connecting Wiring to the 63
- FLEX Ex I/O Analog 63
- ATTENTION 64
- Ground the Module 66
- ControlNet Network 69
- Using Programming 70
- Software in Your FLEX Ex 70
- Application 70
- About the ControlNet Ex 70
- Communication Over the 71
- FLEX Ex Backplane 71
- Unscheduled Data Transfer 72
- Module I/O Mapping 72
- I/O Structure 73
- Fault State Data 75
- Device Actions 75
- Calibrate Your Module 77
- When and How to Calibrate 78
- Your FLEX Ex Analog I/O 78
- Tools and Equipment 78
- 1797-IE8H Calibration 79
- Features 79
- Command Structure 80
- 2 Calibrate gain at 25 °C 81
- °C Channel-Mask 82
- 25 °C according to 83
- . During the 87
- 1797-OE8H Calibration 88
- Calibration) 96
- Evaluate the Application 99
- Define the Area 100
- Classification 100
- Select Protection 101
- Method(s) 101
- Match Field Devices and 101
- I/O Modules 101
- Optimize Power 105
- Distribution 105
- Assigning Power Supplies 106
- Safe Area 107
- Hazardous Area 107
- Chapter Summary 108
- Troubleshoot the FLEX Ex 109
- Analog I/O Modules 109
- 8 CHANNEL ANALOG OUTPUT 110
- Specifications 113
- Class I Division 1 Hazardous 114
- Specifications A-3 115
- Wiring Methods 116
- IMPORTANT 117
- A-6 Specifications 118
- Specifications A-9 121
- 1797-OE8H Output Module 122
- Specifications A-11 123
- A-12 Specifications 124
- FLEX Ex HART Module Commands 125
- Universal Commands 126
- Common Practice 127
- Commands 127
- Device-specific Commands 127
- Command 129 128
- Command 130 130
- Command 131 131
- Command 132 132
- Command 133 132
- Command 134 133
- Command 135 134
- Command 136 135
- Command 137 136
- Command 138 137
- Command 139 138
- Command 140 139
- Command 141 140
- Command 143 141
- Command 144 141
- Command 145 142
- Command 146 143
- Command 147 144
- Command 148 144
- Command 149 145
- Command 152 145
- Command 154 146
- Command 158 147
- Command 159 148
- Command 164 148
- Appendix 149
- What This Appendix 149
- Contains 149
- Message Structure 149
- Transaction Procedure 150
- Burst Mode (not supported) 150
- Preamble 151
- Start Character 151
- HART Address 151
- HART Command 152
- Byte Count 152
- Check Byte 152
- Response Code 153
- Background Information 165
- Configuration 166
- Analog Fault State 168
- Fault Mode 168
- Local Fault Mode 168
- Latch Retry Mode 169
- Analog/Digital Mode 169
- Digital Fault State 170
- Analog Fault State Values 170
- Digital Output Data 171
- Global Reset Bit 171
- Analog Output Data 171
- Diagnostic Status Data 172
- HART Rebuild Bit 172
- Fault Alarm 172
- HART Failure 173
- HART Readback 173
- HART Communication 173
- HART Transmitter 174
- Filter Cutoff 178
- Up/Down Bit 179
- High and Low Error Level 179
- Square Root Threshold 181
- Analog Input Data 181
- Local Fault 182
- Remote Fault 182
- Diagnostic Status 183
- Communication 185
- Differences Between 187
- Attributes and Assembly 187
- HART Frame Enhancements 190
- 2 192
- How Are We Doing? 193
- BUSINESS REPLY MAIL 194
- Rockwell Automation 196
Související produkty a manuály pro Zařízení Rockwell-automation 1797-OE8H FLEX Ex HART Analog Modules User Manual
Zařízení Rockwell-automation 7000L PowerFlex 7000 Medium Voltage AC Drive C Fra Uživatelský manuál
(350 stránky)
(350 stránky)
Zařízení Rockwell-automation 1794-OE8H FLEX I/O HART Analog Modules User Manual Uživatelský manuál
(146 stránky)
(146 stránky)
Zařízení Rockwell-automation 2711p-RAK15, -RAT15 Adapter Kit for PanelView 1400 Uživatelský manuál
(28 stránky)
(28 stránky)
Zařízení Rockwell-automation 47C626 AutoMax Programming Executive V4.2 Uživatelský manuál
(278 stránky)
(278 stránky)
Zařízení Rockwell-automation DeviceNet Communications for PanelView Plus and Pa Uživatelský manuál
(76 stránky)
(76 stránky)
Zařízení Rockwell-automation 7000A PowerFlex Medium Voltage AC Drive (A Frame) Uživatelský manuál
(208 stránky)
(208 stránky)
Zařízení Rockwell-automation 2711E-NKSW1 Replacement Keyswitch Assembly Uživatelský manuál
(24 stránky)
(24 stránky)
Zařízení Rockwell-automation 7703E Medium Voltage SMC OEM Components - 10-15 kV Uživatelský manuál
(58 stránky)
(58 stránky)
Zařízení Rockwell-automation 2099-BMxxx Kinetix 7000 High Power Servo Drive Lif Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 60-2428 Special Mounting Assembly for Series 5000 Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 6180 RAC6180 Industrial Computers Installation Ins Uživatelský manuál
(32 stránky)
(32 stránky)
Zařízení Rockwell-automation 2711E-ND1 PanelBuilder 1400E Configurator Software Uživatelský manuál
(114 stránky)
(114 stránky)
Zařízení Rockwell-automation 9904-PCIC ControlNet 9904-PCIC Communications Card Uživatelský manuál
(18 stránky)
(18 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce