Rockwell-automation 57C620 AutoMax Programming Executive Version 3.8 Uživatelský manuál Strana 229
- Strana / 298
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AĆ1Processor Module Ports Programmer/Port B
Appendix A
Processor Module Ports
Programmer/Port B
If the personal computer that will be used as a programming terminal for the
Processor module was purchased from Reliance, you will receive with the
computer the proper cable to connect the computer and the Processor module.
WARNING
THE FOLLOWING INSTRUCTIONS ARE INTENDED ONLY TO ALLOW
FABRICATION OF PROPER CONNECTIONS BETWEEN RELIANCE EQUIPMENT
AND
USERĆPRO
VIDED
PROGRAMMING DEVICES. THE USER MUST READ AND
UNDERSTAND ALL APPLICABLE INSTRUCTION MANUALS PRIOR TO
OPERATING THE EQUIPMENT. FAILURE TO OBSERVE THIS PRECAUTION
COULD RESULT IN BODILY INJURY.
If it is necessary to prepare a cable to connect a programming terminal to the
RSĆ232 port labeled Programmer/Port B" on the leftmost Processor in the
AutoMax rack, follow the steps outlined below.
1. Determine whether your programming terminal contains a 9Ć or 25Ćpin male
connector.
2. Cut a suitable length (not to exceed 10 feet) of 22Ćgauge, multiĆconductor
cable.
3. Follow the connector manufacturer's instructions and make cable
connections using figure 1 or 2, whichever is applicable.
4. Check for grounds, shorts, and continuity using an Ohm meter.
5. Read and understand all applicable Reliance instruction manuals before
connecting the cables to Reliance equipment.
Programming Terminal End
25ĆPin F
emale Connector
Reliance End
25ĆPin Male Connector
SIGNAL PIN#
RECV ă3
XMIT ă2
CTS ă5
RTS ă4
DTR 20
DSR ă6
COM ă7
PIN# SIGNAL
ă2 XMIT
ă3 RECV
ă4 RTS
ă5 CTS
ă6 DSR
20 DTR
ă7 COM
Figure 1
- 1
- 1
- r 1
- 1
- 1
- Table of Contents 3
- 10
- 12
- 13
- 1.0 INTRODUCTION 15
- 17
- 20
- 20
- 21
- 21
- 1.4.6 Network Communication 22
- 2.0 INTRODUCTION TO THE 23
- AutoMax DISTRIBUTED 23
- CONTROL SYSTEM 23
- Executive Overview 24
- Variables 26
- 2.5 AutoMax Help Screens 28
- 3.0 NOTES ON INSTALLATION 29
- Computer 30
- 31
- 3.4.1 Serial Connection 32
- 3.5 User Ports 33
- 4.0 GETTING AROUND IN THE 35
- AutoMax EXECUTIVE AND 35
- 36
- 37
- 4.5 Inactive Commands 38
- 39
- 4.8 Moving a Window Or Icon 40
- 4.10 Enlarging a Window 41
- 42
- 43
- 44
- (DoubleĆClicking) 45
- 4.18 Directory Structure 46
- 47
- 48
- 4.21 Text Editor 49
- 4.22 PC Editor 49
- 51
- 51
- 4.22.7 Searching for a V 56
- 57
- 57
- 58
- 5.1.3 Removing a System 59
- 60
- 5.1.7 Transferring a System 61
- 5.1.9 Selecting 68
- All Systems 68
- 5.2 Section Menu 69
- 70
- 5.2.3 Removing a Section 71
- Printing Section Files 71
- 5.2.7 Transferring a Section 72
- 5.3 Rack Menu 74
- 5.3.3 Removing a Rack 75
- 80
- 5.3.8 Transferring a Rack 81
- 5.3.9 Importing a Rack from 83
- 5.4 Commands Menu 86
- 5.4.1 Editing 87
- DOS Files 87
- 5.5 Setup Menu 95
- 97
- 99
- 6.1 Adding a Module to a Rack 101
- Configuring Remote Heads 105
- Unsupported Module 107
- 6.10 GoTo Menu 110
- 7.0 CONFIGURING VARIABLES 113
- Descriptions 122
- 7.7 Variables Menu 122
- 7.7.2 Updating the Database 124
- 126
- 126
- 7.8 GoTo Menu 127
- 129
- 129
- 131
- 133
- 8.4 Removing a Task 134
- 8.6 Editing a Task 134
- 135
- 135
- 8.10 Transferring Task Files 136
- 138
- 8.13 Resequencing a Task 140
- 8.14 Selecting All Tasks 140
- 8.16 Commands Menu 140
- 8.16.2 Purge 141
- Functions 142
- 9.0 SYSTEM SECURITY 143
- Changing the P 146
- System File 146
- 147
- 147
- 10.0 AutoMax PROCESSOR 149
- OVERVIEW 149
- 10.4 Battery BackĆUp 151
- 10.7 Status Indicators 152
- 10.8 PowerĆUp Initialization 152
- 10.9 RunĆTime Diagnostics 153
- 10.10 Status Codes 153
- 10.11 ShutĆDown Faults 153
- 10.12 StopĆAll Faults 153
- UDC Tasks in the Rack 155
- 159
- 11.1 ON LINE Menu Options 160
- 11.2 ON LINE Menu Security 160
- 11.3 ON LINE Menu Display 160
- 12.0 ON LINE MENU: CONNECT 163
- 12.2 Setting Access 164
- 12.3 Releasing Access 165
- 12.4 Setting AUTOĆRUN 165
- Fragmentation 166
- 12.5.2 Network Communication 167
- 13.0 ON LINE MENU: INFO/LOG 171
- 14.0 ON LINE MENU: TRANSFER 175
- 14.3.1 Utility Tasks 178
- 14.4.1 Save Option: /All 178
- 14.5 Recovering a Rack 179
- 15.0 ON LINE MENU: 181
- RUNNING TASKS 181
- 16.0 ON LINE MENU: 185
- STOPPING TASKS 185
- 17.0 ON LINE MENU: 187
- DELETING TASKS 187
- 18.0 ON LINE MENU: 189
- MONITORING AND EDITING 189
- 18.1.1 Displaying a Variable 192
- 18.1.6 Modifying a Variable 195
- 18.3.2 Outputting a Variable 206
- 18.4.3 Inserting 211
- a Sequence 211
- Deleting a Sequence 212
- Editing a Sequence 212
- Modifying a Preset 213
- 18.4.7 Forcing a Variable 213
- 18.4.8 Unforcing a Variable 214
- 18.4.9 Resequencing a Task 214
- 18.4.10 215
- 18.5 Forcing Variables 217
- 218
- 18.5.3 Unforcing a Variable 219
- 223
- 223
- 20.0 SOFTWARE 225
- TROUBLESHOOTING 225
- 226
- 20.5 Printing Problems 227
- 20.6 System Errors 227
- Appendix A 229
- 230
- 231
- 232
- 232
- BASIC STOP ALL Error Codes 234
- MultibusT and Processor Bus 234
- STOP ALL Error Codes 234
- Configuration Error Codes 235
- 236
- 236
- 236
- 237
- 238
- 238
- 239
- Appendix D 241
- 243
- Appendix F 245
- Appendix G 253
- Appendix H 255
- 256
- 256
- 256
- Appendix J 257
- 258
- 259
- Object File 260
- File, and Application Tasks 260
- Appendix K 261
- 263
- 267
- 269
- 271
- 272
- 272
- 273
- 274
- 274
- 274
- All Tokens in Library 275
- Hierarchical Locking 275
- the User Name 275
- 276
- 276
- Appendix P 279
- Appendix Q 287
- 289
- Appendix S 291
- Module LEDs Displaying Errors 293
- RELIANCE CONTROLS 295
- For additional information 298
- 1 Allen-Bradley Drive 298
Související produkty a manuály pro Zařízení Rockwell-automation 57C620 AutoMax Programming Executive Version 3.8
Zařízení Rockwell-automation 2711-NP3 Panel Mounting Studs for PanelView 1400 T Uživatelský manuál
(12 stránky)
(12 stránky)
Zařízení Rockwell-automation 57C411 Module Specs Resolver Input Module Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 2092-DAx Ultra1500 Host Commands for Serial Commun Uživatelský manuál
(70 stránky)
(70 stránky)
Zařízení Rockwell-automation 8520-OM Offline Development System User Manual Uživatelský manuál
(100 stránky)
(100 stránky)
Zařízení Rockwell-automation 1798-OB8E FlexArmor 24V dc Sourcing Output Modules Uživatelský manuál
(12 stránky)
(12 stránky)
Zařízení Rockwell-automation CENTERLINE MCC Hinge Assembly Instruction for 1/2 Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 7000 PowerFlex Medium Voltage Air-Cooled (B Frame) Uživatelský manuál
(96 stránky)
(96 stránky)
Zařízení Rockwell-automation 2711P-RAK12e Adapter Kit for PanelView 1200/1200E/ Uživatelský manuál
(8 stránky)
(8 stránky)
Zařízení Rockwell-automation 6159 Industrial 17 inch CRT Monitors, Series B Uživatelský manuál
(36 stránky)
(36 stránky)
Zařízení Rockwell-automation 2705 RediSTATION Operator Interface User Manual Uživatelský manuál
(64 stránky)
(64 stránky)
Zařízení Rockwell-automation 2080-LC20-20QWB_20AWB_20QBB_20QWBR_20AWBR_20QBBR M Uživatelský manuál
(24 stránky)
(24 stránky)
Zařízení Rockwell-automation 2727-M7P20D1P1, -M7P20D1Q2, -M7P20D1Q3 MobileView Uživatelský manuál
(148 stránky)
(148 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce