Rockwell-automation 2092-DAx Ultra1500 Host Commands for Serial Commun Uživatelský manuál stáhnout pdf (Strana 15)

Publication 2092-RM001A-EN-P — March 2005

Command Reference 2-3

Fault Reset (RST)

Monitor Variable (MDM)

Command: RST

Description: Clear fault

Format: STX ID # RST : BSS ETX

Response: ACK

Usage Note: Fault Reset will have no effect if action was not taken to resolve the

problem causing the fault.

Command: MDM

Description: Monitor variables

Format: STX ID # MDM P1 P2 P3 P4 P5 : BSS ETX

Data: Argument Description

P1-P5

Variables to monitor.

Refer to Monitor Variables on page A-3 for the

list of variables.

Usage Note: MDM command can monitor up to 5 variables. See Appendix A for

the list of variables.

Response Format: STX ID $ MDM V1&V2&V3&V4&V5 : BSS ETX

Response Data: Argument Description

V1 to V5 Variable values are 4 or 8 bytes signed

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 69 70

Ultra1500 1
Host Commands for 1
Communication 1
Important User Information 2
Table of Contents 3
Table of Contents iii 5
Appendix A 6
Error Codes, Warnings, and 6
Monitor Variables 6
Preface 7
Contents of this Manual 8
Related Documentation 8
Conventions Used in this 8
Allen-Bradley Support 9
P-4 Preface 10
Communications Protocol 11
Checksum 12
Command Reference 13
Set Parameter (STR) 14
Set Parameter (CHP) 14
Fault Reset (RST) 15
Monitor Variable (MDM) 15
2-4 Command Reference 16
Figure 2-1 17
2-6 Command Reference 18
Command Reference 2-7 19
Figure 2-2 20
Read Fault Contents (EHY) 21
Jog (JOG) 21
Read Drive Status (STS) 22
Enable Drive (SVRON) 24
Disable Drive (SVROF) 24
Drive Reset (HWR) 25
Parameters 26
[Pr – 0.02] Basic Modes 28
[Pr – 0.04] Inertia Ratio 29
2-18 Command Reference 30
[Pr – 0.13] Drive Address 32
Group 1 Parameters 33
2-22 Command Reference 34
Operating Mode: All 35
2-24 Command Reference 36
Group 2 Parameters 37
2-26 Command Reference 38
Group 3 Parameters 40
Group 4 Parameters 42
Group 5 Parameters 44
[Pr – 5.03] Up to Speed 45
[Pr – 5.04] Zero Clamp 45
[Pr – 5.06] Disable Delay 45
2-34 Command Reference 46
Group 6 Parameters 48
2-38 Command Reference 50
Group 9 Parameters 51
[Pr – 9.07] Encoder Type 52
[Pr – 9.08] Hall Offset 52
[Pr – 9.20] Motor Thermostat 54
2-44 Command Reference 56
2-46 Command Reference 58
[Pr – 9.60] Displayed Units 59
2-48 Command Reference 60
Appendix 61
Error Codes 61
Warnings 62
Variable 64
Name Ultraware Name Unit 64
(Pr – 6.01) 2-36 65
(Pr – 6.00) 2-36 65
I-2 Index 66
Index I-3 67
I-4 Index 68

Komentáře k této Příručce

Žádné komentáře

Rockwell-automation 2092-DAx Ultra1500 Host Commands for Serial Commun Uživatelský manuál Strana 15

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Rockwell-automation 2092-DAx Ultra1500 Host Commands for Serial Commun