Rockwell-automation 20-750-BNETIP BACnet/IP Option Module Uživatelský manuál Strana 29
- Strana / 88
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Rockwell Automation Publication 750COM-UM005B-EN-P - June 2014 29
Configuring the Option Module Chapter 3
Setting the Device Port
Setting the Device Port enables BACnet messaging to be sent and received by the
option module over the BACnet/IP network. Set Device Parameter 19 - [Device
Port] to a value suitable for your application. By default, it is set to 47808.
Setting a Fault Action
By default, when communication is disrupted (for example, the network cable is
disconnected) or the controller is idle, the drive responds by faulting if it is using
I/O from the network. You can configure a different response to these faults:
• Disrupted I/O communication by using Host Parameter 33 - [Comm Flt
Action].
• An idle controller by using Host Parameter 34 - [Idle Flt Action].
Changing the Fault Action
Set the values of Host Parameters 33 - [Comm Flt Action] and 34 - [Idle Flt
Action] to an action that meets your application requirements.
ESC
ENTER
Stopped
0.00 Hz
Edit Device Port
47808
0 << 60000
AUTO
F
ATTENTION: Risk of injury or equipment damage exists. Host
Parameters 33 - [Comm Flt Action] and 34 - [Idle Flt Action] let you
determine the action of the option module and connected drive if
communication is disrupted or the controller is idle. By default, these
parameters fault the drive. You can configure these parameters so that the
drive continues to run, however, precautions must be taken to verify that
the settings of these parameters do not create a risk of injury or equipment
damage. When commissioning the drive, verify that your system responds
correctly to various situations (for example, a disconnected network cable
or controller in idle state).
Value Action Description
0 Fault The drive is faulted and stopped. (Default).
1 Stop The drive is stopped, but not faulted.
2 Zero Data The drive is sent ‘0’ values for data. This does not command a stop.
3 Hold Last The drive continues in its present state.
4 Send Flt Cfg The drive is sent the data that you set in the fault configuration parameters
(Host Parameters 37 - [Flt Cfg Logic] and 38 - [Flt Cfg Ref]).
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Understanding Parameter 12
- Compatible Products 13
- Required Equipment 13
- Safety Precautions 15
- Quick Start 16
- Installing the Option Module 17
- Setting the IP Address 18
- Selection Jumper 18
- Connecting the Option 19
- Module to the Drive 19
- Module to the Network 19
- Applying Power 20
- Commissioning the Option 23
- Configuring the Option Module 25
- Using the PowerFlex 20 26
- HIM-A6 or 20-HIM-C6S HIM 26
- Setting the Option Module 26
- Address Using Parameters 26
- Setting the Device Instance 28
- Setting the Device Port 29
- Setting a Fault Action 29
- 0<<4 30
- Setting the Comm Loss Time 31
- Setting Web Page Access 32
- Resetting the Option 33
- Restoring Option Module 34
- Parameters to Factory 34
- Defaults 34
- Viewing the Option Module 35
- Status Using Parameters 35
- Updating the Option 35
- Module Firmware 35
- BACnet Services 37
- Understanding BACnet 38
- Basic Drive Operation on 39
- Supported BACnet Objects 40
- Troubleshooting 43
- PORT Status Indicator 44
- MOD Status Indicator 44
- NET A Status Indicator 45
- Viewing Option Module 45
- Diagnostic Items 45
- Viewing and Clearing 47
- Enabling the Option Module 51
- Web Pages 51
- Viewing the Web Pages 51
- IMPORTANT 52
- Process Display Pop-up 54
- Dialog Box 54
- BACnet/IP Configuration 55
- Web Page 55
- Configure E-mail 56
- Notification Web Page 56
- 3. Click Save Changes 58
- Device Information Pages 59
- Specifications 63
- Environmental 64
- Regulatory Compliance 64
- Option Module Parameters 65
- About Parameter Numbers 66
- How Parameters Are 66
- Organized 66
- Device Parameters 66
- Host Parameters 69
- Reset Required: No 70
- 750-Series Drives 71
- Logic Status Word 72
- Conformance Statement 73
- List all BACnet 74
- Interoperability Building 74
- Blocks Supported 74
- (Annex K) 74
- Segmentation Capability 74
- Standard Object Types 75
- Supported 75
- Data Link Layer Options 76
- Device Address Binding 76
- Networking Options 76
- Network Security Options 76
- Character Sets Supported 76
- Glossary 77
- Rockwell Automation Support 88
- Documentation Feedback 88
Související produkty a manuály pro Zařízení Rockwell-automation 20-750-BNETIP BACnet/IP Option Module
Zařízení Rockwell-automation 284D- ArmorStart Base and Control Module Replaceme Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 20-750-PNET Profinet Single Port Option Module Uživatelský manuál
(96 stránky)
(96 stránky)
Zařízení Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Uživatelský manuál
(144 stránky)
(144 stránky)
Zařízení Rockwell-automation 445L GuardShield Safe 4 and Safe 4 PAC Safety Ligh Uživatelský manuál
(40 stránky)
(40 stránky)
Zařízení Rockwell-automation 160 Supplement-160-NX3 Chassis Mount Series C Uživatelský manuál
(12 stránky)
(12 stránky)
Zařízení Rockwell-automation 140U Q, M frame CB Electronic RMS Trip Unit instal Uživatelský manuál
(14 stránky)
(14 stránky)
Zařízení Rockwell-automation 440N SensaGuard Magnetically Coded NonContact Swit Uživatelský manuál
(12 stránky)
(12 stránky)
Zařízení Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Uživatelský manuál
(6 stránky)
(6 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce