Rockwell-automation 1560E SMC Flex Smart Motor Controller Uživatelský manuál Strana 118
- Strana / 198
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
8-10 Communications
1560E-UM050B-EN-P - June 2013
Configuring DataLinks DataLinks are supported in the SMC-Flex. A DataLink is a mechanism
used by most drives to transfer data to and from the controller without
using an Explicit Message. The SMC-Flex supports 16-bit DataLinks,
therefore the device can be configured to return up to four additional
pieces of information without the need for an explicit message.
Rules for Using DataLinks
• Each set of DataLink parameters in an SMC-Flex can be used by only
one adapter. If more than one adapter is connected, multiple adapters
must not try to use the same DataLink.
• Parameter settings in the SMC determine the data passed through the
DataLink mechanism.
• When you use a DataLink to change a value, the value is not written to
the Non-Volatile Storage (NVS). The value is stored in volatile memory
and lost when the drive loses power.
Parameters 88 to 103 are used to configure the DataLinks. For additional
information regarding DataLinks, refer to the user manual for the
communication interface being used.
Note: Node addressing of the DPI communication card can be
programmed via software or a hand-held DPI HIM. The on-board
HIM cannot be used to address the communication card.
Updating Firmware The latest version of firmware and instructions for the SMC-Flex can be
obtained from www.ab.com.
Note: The MV SMC-Flex must use firmware release 3.006 or later.
- Medium Voltage 1
- SMC Flex™ 1
- Motor Controller 1
- Important User Information 2
- Table of Contents 3
- Installation Chapter 2 4
- Programming Chapter 4 5
- Metering Chapter 5 Page 6
- Options Chapter 6 6
- Diagnostics Chapter 7 6
- Communications Chapter 8 6
- Maintenance Chapter 10 7
- Appendix D Spare Parts 8
- Appendix E Accessories 8
- 1560E-UM050B-EN-P - June 2013 10
- Product Overview 11
- 1560E – Retrofit Controller 12
- SMC-Flex™ Control Module 12
- Figure 1.1– Soft Start 13
- Selectable Kickstart : 14
- Current Limit Start ; 14
- Dual Ramp Start : 15
- Full Voltage Start 15
- Preset Slow Speed 16
- Product Overview 1-7 17
- Soft Stop 18
- Overload 19
- Protection and Diagnostics 20
- Underload : 21
- Undervoltage ; 21
- Overvoltage ; 21
- Ground Fault 23
- Table 1.A –PTC Input Ratings 25
- Excessive Starts/Hour 27
- Overtemperature 27
- Figure 1.14 – DPI Location 28
- Pump Control Option 29
- 1-20 Product Overview 30
- Braking Control Option 31
- Power Module 32
- Interface Board 33
- 1-24 Product Overview 34
- Product Overview 1-25 35
- 1-26 Product Overview 36
- Product Overview 1-27 37
- 1-28 Product Overview 38
- 1-30 Product Overview 40
- Product Overview 1-31 41
- 1-32 Product Overview 42
- Product Overview 1-33 43
- Product Overview 1-35 45
- 1-36 Product Overview 46
- Product Overview 1-37 47
- 1-38 Product Overview 48
- Installation 49
- 2-2 Installation 50
- Mounting 51
- Grounding Practices 52
- (with LV panels not shown) 54
- Installation 2-7 55
- Installation 2-9 57
- Power Connections (cont.) 58
- Bulletin 1503E 59
- 2-12 Installation 60
- Installation 2-13 61
- 2-14 Installation 62
- Installation 2-15 63
- Surge Arrestor Protection 64
- Two-speed Motors 65
- Multi-motor Protection 65
- EMC Compliance 66
- Wire Size Torque 67
- 0.75 to 2.5 mm 67
- 2-20 Installation 68
- Commissioning Procedure 69
- System Characteristics 70
- MV SMC-Flex™ Module 71
- 3-4 Commissioning Procedures 72
- Commissioning Procedures 3-5 73
- 3-6 Commissioning Procedures 74
- Figure 3.3 – Interface PCB 75
- 3-8 Commissioning Procedures 76
- Milliseconds 77
- Control Function Tests 78
- Programming 81
- Programming Menu (cont.) 82
- Programming 4-3 83
- Table 4.A 84
- Parameter Linear List 84
- Programming 4-5 85
- EscEsc SelSel 86
- Using Parameter Management 87
- (Dual Ramp) 90
- Parameter Option 91
- Starting Mode 91
- Full Voltage 91
- Basic Setup (cont.) 92
- Undervoltage u 94
- Overvoltage u 94
- Underload v 94
- Motor Data Entry 95
- 4-16 Programming 96
- Metering 97
- Viewing Metering Data 98
- Human Interface Module 100
- Programming Parameters 102
- Options 6-5 103
- 6-6 Options 104
- Diagnostics 105
- 7-2 Diagnostics 106
- Table 7.A 107
- Fault Code Cross-Reference 107
- 7-4 Diagnostics 108
- Communications 109
- Keypad Description 110
- Communications 8-3 111
- Control Enable 112
- Communications 8-5 113
- Loss of Communication and 114
- Network Faults 114
- Table 8.E 115
- SMC-Flex Bit Identification 116
- Scale Factors for PLC 117
- Communication 117
- Rules for Using DataLinks 118
- Troubleshooting 119
- : Prestart fault indication 121
- Troubleshooting 9-5 123
- 9-6 Troubleshooting 124
- Voltage Feedback Circuit 125
- Voltage-Sensing Board 126
- Replacement 126
- Figure 9.3 – IGDPS Board 127
- 9-10 Troubleshooting 128
- Troubleshooting 9-11 129
- SCR Replacement Procedure 131
- Power Circuit 132
- Troubleshooting (cont.) 132
- Troubleshooting 9-15 133
- Troubleshooting 9-17 135
- Figure 9.6 – Heatsink Clamp 136
- Troubleshooting 9-19 137
- Figure 9.9 – Heatsink Clamp 138
- Troubleshooting 9-21 139
- Troubleshooting 9-23 141
- 9-24 Troubleshooting 142
- Troubleshooting 9-25 143
- Snubber and Resistor Circuit 145
- VOLTAGE FEEDBACK 146
- Troubleshooting 9-29 147
- 9-30 Troubleshooting 148
- Troubleshooting 9-31 149
- 9-32 Troubleshooting 150
- Troubleshooting 9-33 151
- 9-34 Troubleshooting 152
- Troubleshooting 9-35 153
- 9-36 Troubleshooting 154
- Troubleshooting 9-37 155
- 9-38 Troubleshooting 156
- Troubleshooting 9-39 157
- 9-40 Troubleshooting 158
- Maintenance 159
- Vacuum Bottles 160
- Terminals 160
- Solid-State Devices 161
- Static-Sensitive Items 161
- Final Check Out 161
- 10-4 Maintenance 162
- Environmental Considerations 163
- Appendix A 165
- A-2 Specifications 166
- Bulletin 1560E 169
- Bulletin 1562E 169
- Description Specifications 170
- Description 172
- Parameter Information 173
- Parameter Information B-3 175
- B-4 Parameter Information 176
- 1560E and 1562E Relay Control 177
- SMC-Flex module 178
- Spare Parts 187
- Table D.2 188
- Spare Parts D-3 189
- Table D.4 190
- Table D.6 192
- Table D.7 193
- Accessories 194
- Table D.8 194
- E-2 Accessories 196
Související produkty a manuály pro Zařízení Rockwell-automation 1560E SMC Flex Smart Motor Controller
Zařízení Rockwell-automation 1606-XLP60BQT Power Supply Reference Manual Uživatelský manuál
(24 stránky)
(24 stránky)
(42 stránky)
Zařízení Rockwell-automation 1492-AIFMQS 4 Input / 4 Output Fusible Analog Inte Uživatelský manuál
(6 stránky)
(6 stránky)
Zařízení Rockwell-automation 1492-CM800-LD009 Field Wire Conv. Module for Modic Uživatelský manuál
(6 stránky)
(6 stránky)
Zařízení Rockwell-automation 1492-IFM20DS24-4_IFM20DS120-4 8 Point Isolated Int Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 1512A MV Controllers - 800A One-High Cabinet Uživatelský manuál
(105 stránky)
(105 stránky)
Zařízení Rockwell-automation 1492-XIMTRxxx_RXIMTRxxx 16 and 32 Point Relay Inte Uživatelský manuál
(6 stránky)
(6 stránky)
Zařízení Rockwell-automation 1585BP Bulkhead Coupler Installation Instructions Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 1492-CM1771-LD001 Digital I/O Conversion Module Uživatelský manuál
(8 stránky)
(8 stránky)
Zařízení Rockwell-automation 1102C-PKxx 400A / 600A Vacuum Contactor AC Coil Re Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 1336T Function Block Prog. Manual, Series A/B Uživatelský manuál
(180 stránky)
(180 stránky)
(43 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce