Rockwell Automation 1203-SSS Uživatelský manuál stáhnout pdf (Strana 31)

Installing the Converter 2-13

PowerFlex 1203-USB Converter User Manual

Publication DRIVES-UM001D-EN-P

Removing the Converter

1. Disconnect the cable from the drive, and then from the converter.

To disconnect the cable, press on the cable latch and then pull it out.

2. Disconnect the USB cable from the converter, and then from the

computer.

ATTENTION: Risk of injury or equipment damage exists. If the

converter is transmitting control I/O to the drive (indicated by a

steady green Diamond status indicator), the drive may fault when

you remove or reset the converter. Determine how your drive will

respond before removing or resetting a connected converter.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 111 112

PowerFlex 1203-USB Converter 1
Important User Information 2
Summary of Changes 3
Table of Contents 5
Chapter 4 Troubleshooting 6
Appendix A Specifications 6
Appendix F History of Changes 7
About This Manual 9
Additional Resources 10
Getting Started 11
Components 12
Features 12
Compatible Products 13
Required Equipment 14
User-Supplied Equipment 15
Safety Precautions 16
Quick Start 16
Computer 17
1-8 Getting Started 18
Installing the Converter 19
Installing the USB Drivers 22
Installing the Converter 2-5 23
2-6 Installing the Converter 24
Installing the Converter 2-7 25
2-8 Installing the Converter 26
Installing the Converter 2-9 27
2-10 Installing the Converter 28
Installing the Converter 2-11 29
Installing Connected 30
Components Workbench 30
Software 30
Powering Up the Converter 30
Removing the Converter 31
2-14 Installing the Converter 32
Configuring the Converter 33
Using Connected 34
Configuring the Converter 3-3 35
Configuring the Converter 3-5 37
3-6 Configuring the Converter 38
to open the Linear List 38
Resetting the Converter 39
Updating the Firmware 40
Using RTU Master Mode for 40
Configuring the Converter 3-9 41
Establishing Communication 42
to open the RSWho window 45
Troubleshooting 49
Diamond Status Indicator 50
RX Status Indicator 50
TX Status Indicator 50
Converter Diagnostic Items 51
Viewing Diagnostic Data 52
Troubleshooting 4-5 53
Converter Events 54
Event Codes for DSI Drives 55
Viewing and Clearing 56
Viewing and Clearing DF1 57
Communication Statistics 57
Troubleshooting Potential 58
Problems 58
Specifications 59
Environmental 60
Agency Certification 60
Converter Parameters 61
Parameters – DSI Drives 62
Parameters – SCANport 64
Drives (DriveExplorer or 64
DriveExecutive software 64
Appendix C 65
Preparing for a Firmware 68
Viewing and Clearing Events 70
Appendix D 75
Appendix E 91
Updating Firmware 95
History of Changes 99
F-2 History of Changes 100
Glossary 101
D DF1 Protocol 102
N NVS (Non-Volatile Storage) 103
S SCANport 104
U Update 104
X Xmodem 104
Z Zero Data 105
G-6 Glossary 106
Rockwell Automation Support 112
Documentation Feedback 112

Komentáře k této Příručce

Žádné komentáře

Rockwell Automation 1203-SSS Uživatelský manuál Strana 31

Komentáře k této Příručce

Související produkty a manuály pro Sítě Rockwell Automation 1203-SSS