Rockwell-automation 20P PowerFlex DC Drive - Frame D SCR Module Leg As Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Rockwell-automation 20P PowerFlex DC Drive - Frame D SCR Module Leg As. Rockwell Automation 20P PowerFlex DC Drive - Frame D SCR Module Leg Assembly User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 10
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Publication 20P-IN054A-EN-P
PowerFlex® DC Drive
Frame D SCR Module Leg Assembly
Installation Instructions
What This Kit Includes
Three SCR module leg assemblies
Three (for non-regenerative drives) or six (for regenerative drives) gate lead
cable sets
Static strap
Tools That You Need
Flathead screwdriver
Hexalobular screwdrivers
Torque wrenches
What You Need to Do
To install the SCR module leg assemblies:
Step 1: Remove power from the drive
Step 2: Remove the protective cover and open the control panel
Step 3: Remove the existing SCR module leg assemblies
Step 4: Install the new SCR module leg assemblies
Step 5: Close the control panel, install the protective cover and document
the change
ATTENTION: Only qualified personnel familiar with DC drives
and associated machinery should plan or implement the installation,
start-up and subsequent maintenance of the system. Failure to comply
may result in personal injury and/or equipment damage.
ATTENTION: To avoid an electric shock hazard, ensure that all
power to the drive has been removed before performing the following.
Zobrazit stránku 0
1 2 3 4 5 6 7 8 9 10

Shrnutí obsahu

Strany 1 - Installation Instructions

Publication 20P-IN054A-EN-PPowerFlex® DC DriveFrame D SCR Module Leg AssemblyInstallation InstructionsWhat This Kit Includes• Three SCR module leg ass

Strany 2 - Protective Cover and Open

Publication 20P-IN054A-EN-P - January 2011Copyright © 2011 Rockwell Automation. All rights reserved. Printed in USA.www.rockwellautomation.comAmericas

Strany 3 - Remove DPI cable

Publication 20P-IN054A-EN-P2Step 1: Remove Power from the Drive• Remove and lock-out all incoming power to the drive. Step 2: Remove the Protective Co

Strany 4 - Assemblies

3Publication 20P-IN054A-EN-P2. Disconnect the DPI cable from the HIM (if present).3. Insert a flathead screwdriver into the holes in the right side of

Strany 5 - Publication 20P-IN054A-EN-P

Publication 20P-IN054A-EN-P4Step 3: Remove the Existing SCR Module Leg AssembliesImportant:Note the terminal number on the fuse switch to which the si

Strany 6

5Publication 20P-IN054A-EN-PImportant:Mark all connections and wires before removal to avoid incorrect wiring during reassembly.4. Disconnect the gate

Strany 7

Publication 20P-IN054A-EN-P67. Remove the four bolts and washers that secure each SCR module leg assembly output terminal to a DC output bus bar (C an

Strany 8 - SCR Module Leg

7Publication 20P-IN054A-EN-PImportant:Prior to removing the SCR assemblies, ensure that the area around the drive is clear of equipment. Only lift the

Strany 9 - Related Documentation

Publication 20P-IN054A-EN-P811. If you are reusing the bimetal thermostat mounted on the left SCR module leg assembly, disconnect the wires from the c

Strany 10

9Publication 20P-IN054A-EN-PStep 5: Close the Control Panel, Install the Protective Cover and Document the Change1. Close the control panel, replace t

Komentáře k této Příručce

Žádné komentáře