Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Uživatelský manuál stáhnout pdf (Strana 87)

Rockwell Automation Publication 750COM-UM002B-EN-P - October 2012 87

Troubleshooting Chapter 7

14 DPI Baud 500kbps The option module detected that the drive was communicating at 500 Kbps.

15 DPI Host Invalid The option module was connected to an incompatible product.

16 DPI Dup Port Another peripheral with the same port number is already in use.

17 DPI Type 0 Logon The option module has logged in for Type 0 control.

18 DPI Type 0 Time The option module has not received a Type 0 status message within the specified time.

19 DPI DL Logon The option module has logged into a Datalink.

20 DPI DL Error The drive rejected an attempt to log in to a Datalink because the Datalink is not supported or is used by another peripheral.

21 DPI DL Time The option module has not received a Datalink message within the specified time.

22 DPI Ctrl Disable The option module has sent a ‘Soft Control Disable’ command to the drive.

23 DPI Ctrl Enable The option module has sent a ‘Soft Control Enable’ command to the drive.

24 DPI Msg Timeout A Client-Server message sent by the option module was not completed within 1 second.

25 DPI Manual Reset The option module was reset by changing its Reset Module parameter.

SI Events

26 SI Online The option module has logged into the Serial Interface Communication.

27 SI Logon Error The option module failed to log into the Serial Interface.

28 SI Comm Fault The Serial Interface Communication has faulted.

Network Events

29 Net Link Up A network link was available for the option module.

30 Net Link Down The network link was removed from the option module.

31 Net Dup Address The option module uses the same address as another device on the network.

32 Net Comm Fault The option module detected a communication fault on the network.

33 Net Sent Reset The option module received a reset from the network.

34 Net IO Close An I/O connection from the network to the option module was closed.

35 Net Idle Fault The option module received ‘idle’ packets from the network.

36 Net IO Open An I/O connection from the network to the option module has been opened.

37 Net IO Timeout An I/O connection from the network to the option module has timed out.

38 Net IO Size Err The option module received an incorrectly sized I/O packet.

39 PCCC IO Close The device sending PCCC Control messages to the option module has set the PCCC Control Timeout to zero.

40 PCCC IO Open The option module has begun receiving PCCC control messages (the PCCC Control Timeout was previously set to a non-zero value).

41 PCCC IO Timeout The option module has not received a PCCC Control message for longer than the PCCC Control Timeout.

42 Msg Ctrl Open The timeout attribute in either the CIP Register or Assembly object was written with a non-zero value, allowing control messages to be sent to the

option module.

43 Msg Ctrl Close The timeout attribute in either the CIP Register or Assembly object was written with a zero value, disallowing control messages to be sent to the

option module.

44 Msg Ctrl Timeout The timeout attribute in either the CIP Register or Assembly object elapsed between accesses of those objects.

45-46 Reserved —

47 Net Bus Off The network has experienced a Bus Off condition.

48 Net Poll Timeout A Polled I/O connection has timed out.

49 Net IO Frag Err A network I/O fragment was received out of sequence. Possible line noise problem.

50 Net COS Timeout A Change of State (COS) connection has timed out.

Table 12 - Option Module Events (Continued)

Code Event Description

1 2 ... 82 83 84 85 86 87 88 89 90 91 92 ... 143 144

Komentáře k této Příručce

Žádné komentáře

Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Uživatelský manuál Strana 87

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module