Rockwell-automation 1784-KTCS ControlNET Scanner Installation Instruct Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Rockwell-automation 1784-KTCS ControlNET Scanner Installation Instruct. Rockwell Automation 1784-KTCS ControlNET Scanner Installation Instructions User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 32
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Publication 1784-5.35 – April 1999
17
ControlNet Scanner Card
Catalog Number 1784-KTCS
To the Installer
This document describes how to install and use the 1784-KTCS ControlNet
scanner card.
Topic Page
Introducing the KTCS Card
2
Understanding the Application Software 3
Compliance to European Union Directives 3
Configuring the Card Hardware 5
Selecting the Base Memory Address Location 6
Selecting the Base I/O Space Address Location 9
Setting the Jumpers 14
Installing the Card 15
Installing IOLinx Software 16
Running the Installation Check Wizard 19
Connecting the Card 21
Connecting Another Device to ControlNet Through the NAP 23
Connecting the Card Directly to the ControlNet Network 26
Interpreting the Status Indicators 26
Removing IOLinx Software 28
CSA Hazardous Location Approval 29
Specifications 31
Installation Instructions
Zobrazit stránku 0
1 2 3 4 5 6 ... 31 32

Shrnutí obsahu

Strany 1 - ControlNet Scanner Card

Publication 1784-5.35 – April 199917ControlNet Scanner CardCatalog Number 1784-KTCSTo the InstallerThis document describes how to install and use the

Strany 2 - 2 ControlNet Scanner Card

10 ControlNet Scanner CardPublication 1784-5.35 – April 1999Worksheet DKTCS switch settingsBase I/O Address(hex)Switch SettingsBase I/O Address(hex)S

Strany 3 - Low Voltage Directive

ControlNet Scanner Card 11Publication 1784-5.35 – April 1999Worksheet EYour base I/O space addressRecord the base I/O space address for the KTCS card

Strany 4 - Handling the Card

12 ControlNet Scanner CardPublication 1784-5.35 – April 19993. If you are using the card’s default memory address setting, go to step 4.If you are se

Strany 5 - Configuring the Card Hardware

ControlNet Scanner Card 13Publication 1784-5.35 – April 19994. If you are using the card’s default base I/O space address setting, go to thenext sect

Strany 6

14 ControlNet Scanner CardPublication 1784-5.35 – April 1999Setting the JumpersImportant: When you receive your card, the jumpers are in the defaultp

Strany 7 - memory allocation worksheet

ControlNet Scanner Card 15Publication 1784-5.35 – April 1999Installing the CardImportant: Before you install the card, make sure you know how to conf

Strany 8

16 ControlNet Scanner CardPublication 1784-5.35 – April 1999Inserting the CardTo insert the card inside the computer:1. Follow the card handling inst

Strany 9

ControlNet Scanner Card 17Publication 1784-5.35 – April 1999Note: The CD-ROM will carry the Windows Autorun. Once inserted intothe CD-ROM drive, if

Strany 10 - switch settings

18 ControlNet Scanner CardPublication 1784-5.35 – April 19996. Enter your name, company, and product serial number.labelserial number on label7. Clic

Strany 11 - Setting the Card’s Switches

ControlNet Scanner Card 19Publication 1784-5.35 – April 19999. Choose a destination location.You see the Setup progress bar, followed by the “Setup C

Strany 12 - (recommended setting)

2 ControlNet Scanner CardPublication 1784-5.35 – April 1999If you are connecting the card directly to a ControlNet network, you also need toread:• Co

Strany 13

20 ControlNet Scanner CardPublication 1784-5.35 – April 19994. Select the I/O Base Address for this card.Refer to Worksheet E on page 11. Yourecorde

Strany 14 - Setting the Jumpers

ControlNet Scanner Card 21Publication 1784-5.35 – April 199910. Click Next to continue.The wizard prepares to reset the card, and reports Card has be

Strany 15 - Installing the Card

22 ControlNet Scanner CardPublication 1784-5.35 – April 1999Figure 3KTCS card connector1784KTCSNetwork Access Port (NAP)RJ-45 connector for connectin

Strany 16 - Installing IOLinx Software

ControlNet Scanner Card 23Publication 1784-5.35 – April 1999Connecting Another Device to ControlNet Through the Network Access PortBy using the card’

Strany 17

24 ControlNet Scanner CardPublication 1784-5.35 – April 1999Table A shows the wiring for the cable.Table AWiring for 1786-CP connector cableConnector

Strany 18 - C:\Program

ControlNet Scanner Card 25Publication 1784-5.35 – April 1999Figure 5Host computer connected to ControlNet device via 1786-CP cable 1786–CP cable1784–

Strany 19 - ControlNet Scanner Card 19

26 ControlNet Scanner CardPublication 1784-5.35 – April 1999Connecting the Card Directly to the ControlNet NetworkTo connect the card directly to a C

Strany 20 - 20 ControlNet Scanner Card

ControlNet Scanner Card 27Publication 1784-5.35 – April 1999Table BControlNet status interpretation• steady – indicator is on continuously in the def

Strany 21 - Connecting the Card

28 ControlNet Scanner CardPublication 1784-5.35 – April 1999Removing IOLinx SoftwareUse the Start menu or the Add/Remove control panel applet to unin

Strany 22

ControlNet Scanner Card 29Publication 1784-5.35 – April 1999CSA Hazardous Location ApprovalCSA certifies products for general use as well as for use

Strany 23 - RJ-45 8-pin connectors

ControlNet Scanner Card 3Publication 1784-5.35 – April 1999Understanding the Application SoftwareThe Allen-Bradley standard application programming i

Strany 24

30 ControlNet Scanner CardPublication 1784-5.35 – April 1999Approbation d’utilisation dans des emplacements dangereux par la CSALa CSA certifie les p

Strany 25

ControlNet Scanner Card 31Publication 1784-5.35 – April 1999SpecificationsThe operating parameters describe the environment within the KTCS slot.Refe

Strany 26

DH+, FLEX I/O, IOLinx, PanelView, and PLC-5/40C are trademarks of Rockwell Automation.ControlNet is a trademark of ControlNet International.WINtellige

Strany 27 - • flashing – the

4 ControlNet Scanner CardPublication 1784-5.35 – April 1999ATTENTION: This digital apparatus does not exceed the Class Alimits for radio noise emiss

Strany 28 - Removing IOLinx Software

ControlNet Scanner Card 5Publication 1784-5.35 – April 1999Configuring the Card HardwareBefore you install the card, you must set the card’s physical

Strany 29

6 ControlNet Scanner CardPublication 1784-5.35 – April 1999Selecting the Base Memory Address LocationThe host computer and the card exchange data via

Strany 30 - Approbation

ControlNet Scanner Card 7Publication 1784-5.35 – April 1999Worksheet ABase memory allocation worksheetBase Memory Address(hex)Host Computer Assignmen

Strany 31 - Specifications

8 ControlNet Scanner CardPublication 1784-5.35 – April 1999Worksheet BKTCS switch settingsBase Memory Addr(hex)Switch SettingsBase Memory Addr(hex)Sw

Strany 32 - Worldwide representation

ControlNet Scanner Card 9Publication 1784-5.35 – April 1999Selecting the Base I/O Space Address LocationThe host addresses I/O devices on the card by

Komentáře k této Příručce

Žádné komentáře