Rockwell-automation 1769-HSC Compact High Speed Counter Module Uživatelský manuál stáhnout pdf (Strana 117)

Rockwell Automation Publication 1769-UM006E-EN-P - July 2013 117

Diagnostics and Troubleshooting Chapter 5

TIP

The OK status indicator flashes red for all error codes in the

Configuration Error Codes table.

IMPORTANT

Only error codes X400…X443 apply to the packaged controller.

Table 23 - Configuration Error Codes

Hex

Equivalent

(1)

Module

Error

Code

Extended

Error

Information

Code

Error Description

Binary Binary

X400 010 0 0000 0000 General Configuration Error No additional information

X401 010 0 0000 0001 UnusedConfigBitSet One or more of the unused module configuration bits are set.

X402 010 0 0000 0010 BadModConfigUpdate Occurs when you attempt to change a forbidden module

configuration parameter while a counter or range is still enabled.

See

Table 24 on page 120 for a list of the forbidden parameters.

X411 010 0 0001 0001 BadCounterNum_1 Nonzero configuration values were entered for Counter 1, when

Counter 1 was not available.

X412 010 0 0001 0010 BadCounterNum_2 Nonzero configuration values were entered for Counter 2, when

Counter 2 was not available.

X413 010 0 0001 0011 BadCounterNum_3 Nonzero configuration values were entered for Counter 3, when

Counter 3 was not available.

X420 010 0 0010 0000 BadCounterMode_0 Operation Mode_0 is set to an invalid value. For example, value is

reserved (011 or 111) or nonzero when NumberofCounters = 11.

X421 010 0 0010 0001 BadCounterMode_1 Operation Mode_1 is set to an invalid value. For example, value is

reserved (011 or 111) or nonzero when NumberofCounters = 10 or

11.

X430 010 0 0011 0000 BadMin_0 Programmed Ctr0MinCount is greater than the Ctr0MaxCount.

X431 010 0 0011 0001 BadMin_1 Programmed Ctr1MinCount is greater than the Ctr1MinCount.

X432 010 0 0011 0010 BadMin_2 Programmed Ctr2MinCount is greater than the Ctr2MaxCount.

X433 010 0 0011 0011 BadMin_3 Programmed Ctr3MinCount is greater than the Ctr3MaxCount.

X440 010 0 0100 0000 BadPreset_0 The programmed Ctr0Preset is greater than the Ctr0MaxCount or

less than the Ctr0MinCount.

X441 010 0 0100 0001 BadPreset_1 The programmed Ctr1Preset is greater than the Ctr1MaxCount or

less than the Ctr1MinCount.

X442 010 0 0100 0010 BadPreset_2 The programmed Ctr2Preset is greater than the Ctr2MaxCount or

less than the Ctr2MinCount.

X443 010 0 0100 0011 BadPreset_3 The programmed Ctr3Preset is greater than the Ctr3MaxCount or

less than the Ctr3MinCount.

X450 010 0 0101 0000 BadHysteresis_0 The Ctr0Hysteresis value is invalid, that is, less than zero.

X451 010 0 0101 0001 BadHysteresis_1 The Ctr1Hysteresis value is invalid, that is, less than zero.

X452 010 0 0101 0010 BadHysteresis_2 The Ctr2Hysteresis value is invalid, that is, less than zero.

X453 010 0 0101 0011 BadHysteresis_3 The Ctr3Hysteresis value is invalid, that is, less than zero.

X460 010 0 0110 0000 BadScalar_0 The Ctr0Scalar value is invalid, that is, less than one.

X461 010 0 0110 0001 BadScalar_1 The Ctr1Scalar value is invalid, that is, less than one when

NumberofCounters = 01, 10 or 11.

1 2 ... 112 113 114 115 116 117 118 119 120 121 122 ... 169 170

Komentáře k této Příručce

Žádné komentáře

Rockwell-automation 1769-HSC Compact High Speed Counter Module Uživatelský manuál Strana 117

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Rockwell-automation 1769-HSC Compact High Speed Counter Module