Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3 Uživatelský manuál Strana 130
- Strana / 216
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
APPENDIX B
FlexPak 3000 49’1340 e
B-26
MAXIMUM SPEED (P.004)
The maximum speed of the drive that can be supported by the application or process. MAXIMUM
SPEED can be less than or equal to TOP SPEED.
If raising this value causes MINIMUM SPEED to become less than 10% of MAXIMUM SPEED, an alarm
is generated.
Parameter Range: 1 to TOP SPEED (RPM or user-defined units)
Default Setting: 500 RPM
Parameter Type: Tuneable
OIM Menu Path(s): Drive Reference - Drive Reference Limits Quick Start
Refer also to Parameters: TOP SPEED (P.011)
WARNING
The incorrect setting of this parameter can cause an overspeed condition. This parameter must be set
by a qualified person who understands the significance of setting it. Set the value of this parameter
accurately per your application requirements. Failure to observe this precaution could result in bodily
injury.
WARNING
When performing this adjustment, do not allow the motor to exceed the maximum safe speed of the
driven equipment as determined by the equipment manufacturer. Failure to observe this precaution
could result in bodily injury.
METER OUT 1 GAIN ADJ (P.400)
Scales the Meter 1 Output Signal at the regulator board terminal strip.
Parameter Range: 0.100 to 1.900
Default Setting: 1.000
Parameter Type: Tuneable
OIM Menu Path(s): Input/Output - Meter Outputs
NOTE: Testpoint METER OUT FULL SCALE must source METER OUT 1 SELECT for an accurate
adjustment. See Appendix D, figure D.8, for further details.
- FlexPak 3000 Power Module 1
- SW-Version 4.3 1
- Instruction Manual 1
- Table of Contents 3
- 6.0 Quick Start 6-1..6-10 4
- Appendices 5
- List of Figures 6
- List of Tables 6
- 1.1 Safety Instructions 7
- 1.2 General Notes 8
- 1.3 Manual Scope 8
- 1.4 Related User Manuals 8
- 2.1 Drive Identification 9
- 2.2 Drive Specifications 10
- 2.2.6 DC Voltage Ratings: 11
- (-73/43) I 12
- 2.3.1 Logic Inputs: 13
- 2.3.2 Logic Outputs: 13
- 2.3.3 Analog Inputs: 13
- 2.3.4 Analog Outputs: 14
- 2.4 Drive Description 15
- (M/N 317C160D) 16
- (M/N 905FK0101) 16
- 2.5 Controls/Indicators 17
- 2.5.2 Controls 18
- FAULT KEYPAD MANUAL FORWARD 20
- ALARM KEYPAD MANUAL FORWARD 20
- DIAGS KEYPAD MANUAL FORWARD 20
- 3.1 General 25
- 3.3 Install the Drive 25
- 1C 1U 1V 1W 1D 27
- 25 Ø 1) 29
- 3.6 Install the Motor 33
- 3.8 Wire the Drive 34
- 3.8.6 Stopping the Drive 35
- INSTALLATION AND WIRING 38
- 1LG 1 2 03 42
- 4.1 Introduction 43
- 4.2 Test Equipment Needed 43
- 4.3 Power Off Inspection 43
- 4.4 Motor Ground Check 43
- 4.5 Jumper Settings 44
- 4.6 Powering Up the Drive 49
- 4.8 Accessing the Main Menu 50
- Self Tuning 51
- CML Feedback Scaling* 51
- Adjustments 52
- 4.13 Language Selection 53
- 4.14 Programming Features 54
- 4.14.3 Memory Operations 55
- 4.14.4 Reset Clock 56
- 4.14.5 Define User Units 56
- 4.14.5.2 Define Load Units 58
- 5.1 Introduction 59
- " UP 60
- LEFT 60
- & RIGHT 60
- 6.0 Quick Start 63
- 6.1 Introduction 63
- N/A = Not Applicable 69
- 6.4.1 Self Tune Setup 70
- 6.4.2 Execute Self-tuning 71
- 6.5 Final Adjustments 72
- 7.1 General 73
- 7.2 Wiring Errors 73
- 7.3 AC Line and Power Input 73
- 7.4 DC Motor 73
- 7.5 Remote M Contactor 74
- 7.6 Optional Kits 74
- 7.7.2 About The Alarm Menu 75
- 7.7.3 Diagnostics Menu 77
- 7.7.4 Diagnostics Configure 77
- CPU OK LED OIM COMM OK LED 78
- Replacement of a thyristor 82
- 8.2 Accessories 86
- Fuse Holder Dimensions 87
- 80 (110) 88
- L2 L3 PE 89
- (1) (2) 90
- EMC Filters for FlexPak 3000 91
- HF Filter 91
- RFI Filter Selection 92
- E L3 L2 L1 93
- E L3 L2 L1 94
- E L1 L2 L3 95
- LOAD 97
- Terminal 97
- E L3 L2 L1 98
- ∅10.5 ∅10.5 100
- ∅11 ∅12 100
- ∅14 ∅12 100
- FlexPak 3000 49’1340 e 102
- Glossary of Terms 103
- • Application 104
- Typically, it will be 0 106
- ± TOP SPEED 109
- ± MOTOR RATED ARM VOLTS 109
- Frequency Input 113
- (A) terminal 39 113
- (A) terminal 40 113
- (COM) terminal 41 113
- SPEED LOOP 114
- CURRENT LOOP 114
- Installed 116
- Not Installed 116
- • AC TACH is selected 118
- WLD RST\ RATIO 141
- * DISABLED 142
- TOP SPEED 142
- SPEED RAMP 142
- OUTPUT (RPM) 142
- (P.011) 143
- ≠ Network 152
- °, return to step 2 154
- • No Trim 155
- • Incremental 155
- 0 (P.490) 159
- APPENDIX D 169
- FlexPak 3000 D-I 169
- KEYPAD] 169
- D-II FlexPak 3000 49’1340 e 170
- 49’1340 e FlexPak 3000 D-1 171
- 49’1340 e FlexPak 3000 D-3 173
- 49’1340 e FlexPak 3000 D-5 175
- Figure D.6 - Speed Loop 176
- Digital Outputs 1 and 2 177
- Analog and Frequency Outputs 177
- Meter Outputs (n = 1, 2) 178
- 49’1340 e FlexPak 3000 D-9 179
- Figure D.11 - Field Block 181
- Analog Inputs 183
- Level Detectors 1 and 2 184
- APPENDIX E 185
- FlexPak 3000 E-1 185
- FlexPak 3000 49’1340 e 186
- CODE DISPLAY DESCRIPTION 186
- FlexPak 3000 E-3 187
- (P.228) 188
- FlexPak 3000 E-5 189
- FlexPak 3000 E-7 191
- OIM Parameter Menu Tree 193
- APPENDIX F 194
- FlexPak 3000 49'1340 e 194
- FlexPak 3000 F-3 195
- FlexPak 3000 F-5 197
- FlexPak 3000 F-7 199
- 49’1340 e FlexPak 3000 G-1 201
- (continued) 202
- 49’1340 e FlexPak 3000 G-3 203
- 49’1340 e FlexPak 3000 G-5 205
- (on I/O card) 205
- 49’1340 e FlexPak 3000 G-7 207
- EMC Directive 209
- Mounting Instructions 210
- Screen 211
- Screened 3-wire 211
- Shielded 2-wire 211
- Wiring Instruction 212
- APPENDIX J 213
- FlexPak 3000 J-1 213
Související produkty a manuály pro Zařízení Rockwell-automation FlexPak 3000 Power Module SW-Version 4.3
Zařízení Rockwell-automation CS3000 V6.1 MMI FlexPak, GV 3000, Liqui-Flo Uživatelský manuál
(100 stránky)
(100 stránky)
Zařízení Rockwell-automation 440N Ferrocode Coded Magnetic Safety Switch Contro Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation MD60 Serial Converter Module - M/N MDCOMM 232 Uživatelský manuál
(54 stránky)
(54 stránky)
Zařízení Rockwell-automation 20D PowerFlex 700H/S Frame 14 Replacement Power St Uživatelský manuál
(24 stránky)
(24 stránky)
Zařízení Rockwell-automation T8873 Trusted 16 Channel 120V ac Isolated Digital Uživatelský manuál
(18 stránky)
(18 stránky)
Zařízení Rockwell-automation T80015 Application Note Trusted SC300E Migration P Uživatelský manuál
(16 stránky)
(16 stránky)
Zařízení Rockwell-automation 1769-L24ER-QB1B_L24ER-QBFC1B_L27ERM-QBFC1B Compact Uživatelský manuál
(86 stránky)
(86 stránky)
Zařízení Rockwell-automation MMCL Using the Mining, Mineral, and Cement Library Uživatelský manuál
(92 stránky)
(92 stránky)
Zařízení Rockwell-automation 1900 General Handling Procedures for Medium Voltag Uživatelský manuál
(12 stránky)
(12 stránky)
Zařízení Rockwell-automation 20D PowerFlex 700S and 700H Frame 12 DC Bus Connec Uživatelský manuál
(34 stránky)
(34 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce