Rockwell-automation 900 Temperature Controller Communications Function Uživatelský manuál Strana 57
- Strana / 103
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Publication 900-UM004D-EN-E - July 2010
Communications Data 3-15
The table below shows the status details.
Table 3.4 Status Details
Bit
Position
Status Bit Description
01
Status
(lower word)
0 Heater overcurrent (CT1) Not generated Generated
1 Heater current hold (CT1)➊ Updated Hold
2 A/D Converter Error Not generated Generated
3 HS alarm (CT1) OFF ON
4 Spare OFF ---
5 Display range exceeded Not generated Generated
6 Input error Not generated Generated
7 Spare OFF ---
8 Control output (heating) OFF ON
9 Control output (cooling) OFF ON
10 HB (heater burnout) alarm output (CT1) OFF ON
11 HB (heater burnout) alarm output (CT2) OFF ON
12 Alarm 1 OFF ON
13 Alarm 2 OFF ON
14 Alarm 3 ➌ OFF ON
15 Program end output OFF ON
Status
(upper word)
16 Event input 1 OFF ON
17 Event input 2 OFF ON
18 Event input 3 ➋ OFF ON
19 Event input 4 ➋ OFF ON
20 Write mode Backup mode RAM write mode
21 EEPROM RAM = EEPROM RAM ≠ EEPROM
22 Setup area Setup area 0 Setup area 1
23 AT execute/cancel AT canceled AT execution in progress
24 Run/Stop Run Stop
25 Communications writing OFF (disabled) ON (enabled)
26 Auto/manual switch Automatic mode Manual mode
27 Program Start Reset Start
28 Heater overcurrent (CT2) Not generated Generated
29 Heater current hold (CT2) ➊ Update Hold
30 Spare OFF ---
31 HS alarm output (CT2) OFF ON
➊ When the control output ON time is less than 100 ms, the bit is set to “1” and the heater current is held at the last current value.
➋ NA 900-TC8, 900YC16, 900-TC32
➌ Applies to 900-TC8
Note 1: Spare bits are always OFF.
Note 2: When read in setup area 1, the status of the bits will be as follows:
•Overcurrent: Last value held
•A/D converter error: Last value held
•Input error: Last value held
•HB and HS outputs: cleared
•Program end output: cleared
•Current hold: Last value held
•Display Range Exceeded: Last value held
•Heating and Cooling Outputs: cleared
•Alarm Outputs: cleared
- Functions 1
- Important User Information 2
- European Communities (EC) 3
- Directive Compliance 3
- Table of Contents 5
- -ii Table of Contents 6
- Safety Precautions 7
- Conventions Used in This 7
- How to Read Display Symbols 8
- About Communications Methods 9
- Communications 10
- Specifications 10
- Transmission procedure 10
- Interface 11
- Communications Parameter 14
- Communication Parameters 15
- Setting Communications 16
- 900-TCx (CompoWay/F) 17
- Response Frame 18
- Communications Data 19
- Example of End Code 19
- Structure of Command Text 21
- Type Code (Variable Type) 22
- Addresses 22
- Number of Elements 23
- List of Services 23
- Detailed Description of 24
- Services 24
- Response code 25
- Write to Variable Area 26
- Bit Position 28
- Response Code 28
- Read Controller Attributes 31
- Read Controller Status 32
- Echoback Test 33
- Test data 34
- Operation Commands 35
- Response Code List 42
- 3-2 Communications Data 44
- Communications Data 3-3 45
- 3-4 Communications Data 46
- Communications Data 3-5 47
- 3-6 Communications Data 48
- Communications Data 3-7 49
- 3-8 Communications Data 50
- Communications Data 3-9 51
- 3-10 Communications Data 52
- Communications Data 3-11 53
- 3-12 Communications Data 54
- Status Structure 55
- Bit position 56
- Table 3.4 Status Details 57
- Table 3.5 Status 2 Contents 58
- Data Format 59
- CRC-16 Calculation Example 60
- Error Codes 62
- Function List 63
- Variable Area 64
- Detailed Description of the 66
- Write Variable Area 69
- Example Command and Response 72
- Write variable address 73
- Command: 75
- Response: 75
- Variable Area (Setting 83
- Range) List 83
- Advanced 84
- Setting 84
- Table 5.6 89
- Four-byte mode Two-byte mode 89
- Figure 5.1 Status Structure 96
- Figure 5.3 Status 2 Structure 97
- Table 5.11 Status Details 98
- Table 5.12 Status 2 Details 99
- Back Cover 103
Související produkty a manuály pro Zařízení Rockwell-automation 900 Temperature Controller Communications Function
Zařízení Rockwell-automation 1492-CM800-LD002 Field Wire Conv. Module for Modic Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 1203 Serial Communications Module Series A Uživatelský manuál
(68 stránky)
(68 stránky)
Zařízení Rockwell-automation 1608M MegaDySC User Manual, 800 - 2400 A Uživatelský manuál
(44 stránky)
(44 stránky)
Zařízení Rockwell-automation 1492-PRINT110_PRINT220 ClearMark Printer User Manu Uživatelský manuál
(80 stránky)
(80 stránky)
Zařízení Rockwell-automation 1203-CN1 ControlNet Communications Module 1203-CN1 Uživatelský manuál
(152 stránky)
(152 stránky)
Zařízení Rockwell-automation 931S-C2R1D-DC2R Isolator, Limit Value Monitoring Uživatelský manuál
(28 stránky)
(28 stránky)
Zařízení Rockwell-automation 1608P ProDySC Installation Instructions, 200 A Uživatelský manuál
(20 stránky)
(20 stránky)
(16 stránky)
Zařízení Rockwell-automation 1492-CM1771-LD0013F Field Wire Conversion Module Uživatelský manuál
(6 stránky)
(6 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce