Rockwell-automation 42DRP Diffuse/Analog Control Uživatelský manuál stáhnout pdf (Strana 1)

INSTALLATION INSTRUCTIONS PHOTOSWITCH



DIFFUSE/ANALOG CONTROL, BULLETIN 42DRP-5400

IMPORTANT: SAVE THESE INSTRUCTIONS FOR FUTURE USE. FOR ADDITIONAL INFORMATION REFER TO PUBLICATION PG-9000

BULLETIN NUMBER

VOLTAGE

SUPPLY

CURRENT

OUTPUT CHARACTERISTIC

RESPONSE

TIME

OPERATING DISTANCE

PHOTOHEAD POWERBASE

TYPE RATING LEAKAGE

(OFF STATE)

WHITE PAPER

WITH

15 X15

(.38 X .38)

LINEAR

RESPONSE

42DRP- 5400 — — —

Analog Voltage 1--10VDC —

100ms 2-- 1 5 

(.61m--4.57m)

5-- 1 3 

(1.22m--4.27m)

Analog Current 1--20mA —

Two Adjustable Set

Points NPN

100mA 10A

42DTB-5000

TERMINAL

22--28

VDC

70mA

42DCB-5000

CABLE

SPECIFICATIONS:

Voltage Supply to Analog Output (Terminal 2):

Current Output 40VDC Max............................

Voltage Output 0V....................................

Output Indicators

Setpoint A Red LED...................................

Setpoint B Green LED.................................

Setpoint Adjustment Yes................................

Setpoint Output Differential 15%.........................

Slope Selectable Positive or Negative.......................

Reverse Polarity Protection Yes...........................

Transient Noise Protection Yes...........................

Short Circuit Protection Analog Output only................

Analog Output Calibration Yes...........................

Sensing Range Adjustment Yes...........................

Temperature Compensation Yes..........................

Field of View 3........................................

Transmitting LED Infrared, 880nm........................

Operating Environment: NEMA 3, 4, 12, 13, and IP66 (IEC529)

Approvals UL Listed and CSA Certified....................

Housing Material High impact chemically resistant Valox



.....

Ambient Temperature Range -- 4 0

Fto150

F(--40

Cto65

C)..

Relative Humidity 90%.................................

Terminati ons

Cable Base: Supplied with 10 (3m) of 5-conductor,..........

flexible, vinyl-covered cable

Terminal Base: Supplied with #6/32 nickel plated brass.......

pressure type terminals

ACCESSORIES

Optional Mounting Assemblies

PART NUMBER DESCRIPTION

60-1577 Armored Cable Adapter

60-1785 Universal Mounting Assembly

60-1748 Heavy Duty Mounting Assembly

60-2014 Flexi-mount Mounting Assembly

60-2083 Photoguard Heavy Duty Protection

60-2213 Conduit Mounting Adapter

60-2230 Limit Switch Type Mounting Assembly

61--5540 NEMA 7 & 9 Enclosure

OPERATING DISTANCE SELECTION

The maximum operating distance is based on installing the con-

trol in a relatively clean environment. Normal industrial environment

actually ranges from moderately Dusty to extremely Dirty.

Greater operating margin (excess gain) may be required, which

can be obtained by reducing the operating distance of the control.

TYPICAL RESPONSE CURVES

VOLTAGE OUTPUT SLOPE

CURRENT OUTPUT SLOPE

OPERATING DISTANCE

DC CURRENT (mA)

1’

(.3m)

2’

(.6m)

3’

(.9m)

4’

(1.2m)

5’

(1.5m)

6”

(15.24cm)

NEGATIVE

SLOPE

POSITIVE

SLOPE

OPERATING DISTANCE

DC VOLTAGE

1’

(.3m)

2’

(.6m)

3’

(.9m)

4’

(1.2m)

5’

(1.5m)

POSITIVE

SLOPE

NEGATIVE

SLOPE

CALIBRATION PROCEDURES

Before starting the calibration procedures for Analog Output or

Setpoint Output, be sure the control is at the same temperature as it’s

environment; it adjusts after approximately 15 minutes. Setpoint Cal-

ibration is best performed after calibration of the Analog Output has

been completed.

1 2

Shrnutí obsahu

Strany 1

INSTALLATION INSTRUCTIONS PHOTOSWITCHDIFFUSE/ANALOG CONTROL, BULLETIN 42DRP-5400IMPORTANT: SAVE THESE INSTRUCTIONS FOR FUTURE USE. FOR ADDITIONAL INF

Strany 2

Calibration of Analog OutputCalibration of the Analog Output is done with a Voltmeter or anAmmeter. When calibrating the Voltage Output, connect the V