Rockwell-automation 294E ArmorStart LT EtherNet/IP Version - User Manu Uživatelský manuál Strana 152
- Strana / 252
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
152 Rockwell Automation Publication 290E-UM001B-EN-P - June 2012
Chapter 4 Bulletin 290E/291E/294E Programmable Parameters
Clear a Type 1 Fault and Restart the Drive
1. Set Parameter 84 (AutoRestartTries) to a value other than 0.
2. Set Parameter 85 (AutoRestartDelay) to a value other than 0.
Clear an Overvoltage, Undervoltage, or Heatsink OvrTmp Fault without Restarting the Drive
1. Set Parameter 84 (AutoRestartTries) to a value other than 0.
2. Set Parameter 85 (AutoRestartDelay) to 0.
AutoRstrtTries
Set the maximum number of times the drive
attempts to reset a fault and restart.
Parameter Number 84
Related Parameter 85
Access Rule GET/SET
Data Type UINT
Group Advanced Config.
Units —
Minimum Value 0
Maximum Value 9
Default Value 0
ATTENTION: Equipment damage and/or personal injury may result if this
parameter is used in an inappropriate application. Do not use this function
without considering applicable local, national, and international codes,
standards, regulations, or industry guidelines.
- User Manual 1
- Important User Information 2
- General Precautions 3
- Software Requirements 4
- Additional Resources 4
- Installation Assistance 5
- Summary of Changes 7
- New and Updated 7
- Information 7
- European Communities (EC) 9
- Directive Compliance 9
- Low Voltage and EMC 9
- Directives 9
- Introduction 10
- Table of Contents 11
- Chapter 2 12
- Installation and Wiring 12
- Chapter 3 13
- Product Commissioning 13
- Chapter 4 13
- Bulletin 290E/291E/294E 13
- Programmable Parameters 13
- Appendix C 16
- Using DeviceLogix 16
- Product Overview 17
- Features 18
- Feature Description 19
- Network Options 20
- Product Overview Chapter 1 21
- Factory-Installed Options 22
- ArmorStart LT Characteristics 23
- Catalog Number Explanation 24
- Basic Operation 27
- Chapter 1 Product Overview 28
- Motor Circuit 29
- Local I/O 29
- Mode of Operation 30
- Status LEDs and Reset 32
- Electronic Data Sheet (EDS) 33
- Optional HOA Selector 35
- Optional HOA Keypad 35
- Configuration 35
- (Bulletin 290E/291E only) 35
- Bulletin 290E 36
- Bulletin 291E 36
- Keypad with Jog Function 37
- (Bulletin 294E only) 37
- Source Brake Contactor 38
- Cat. No 43
- Wiring Terminal Detail 44
- Branch Circuit Protection 46
- Typical System Example 47
- ArmorConnect Media 48
- ArmorConnect Cable Ratings 49
- Electrical Wiring 50
- Figure 27 - Bulletin 294E VFD 52
- Disconnect 53
- Voltage 53
- Monitoring 53
- USA and Canada Markets 55
- General Wiring 56
- Considerations 56
- Grounding 57
- Power Distribution 58
- AC Line Voltage 58
- Line Reactor 58
- Bulletin 294 Motor Cable 59
- Shielded Cable 60
- Recommended Cord Grips 61
- Shield Terminating Connectors 61
- Electromagnetic 62
- Compatibility (EMC) 62
- Ethernet, DeviceNet, and 63
- I/O Connections 63
- ArmorConnect Power 64
- Media Receptacles 64
- Optional Locking Clip 65
- Static Address Alternative 69
- Using the 70
- Rockwell Automation 70
- BootP/DHCP Utility 70
- Figure 43 - Relation List 71
- Save the Relation List 72
- A DHCP 73
- Embedded Web Server 74
- Network Configuration 75
- Parameter Configuration 76
- How to Add a New Module 78
- Using the Add-On Profile 78
- Electronic Keying 80
- Connections 81
- Configured by 81
- HOA Keypad Option 82
- User Configurable I/O 82
- RSLogix 5000 Add-On Profile 83
- Auto-Generated Tags 85
- Parameter Groups 100
- ArmorStart LT EtherNet/IP 102
- Parameters 102
- Bulletin 290E/291E 102
- Trip Status Group 107
- Basic Configuration Group 111
- Starter Protection Group 112
- User I/O Configuration Group 115
- Advanced Configuration 121
- Bulletin 294E 124
- Motor and Control Group 133
- Speed Control Group 135
- Acceleration 136
- Figure 53 - S Curve 137
- Frequency 148
- DC Injection Braking Mode 149
- Ramp-to-Stop Mode 149
- Min. Derate 151
- No Derate 151
- Max. Derate 151
- IMPORTANT 155
- Diagnostics 157
- Fault Diagnostics 158
- Diagnostics Chapter 5 159
- Quick Reference 160
- Troubleshooting 160
- Fault LED Indications 161
- Bulletin 294E Faults 163
- Specifications 165
- Motor Overload Trip Curves 170
- (Used with ArmorStart LT) 171
- Appendix A 179
- ArmorStart LT 180
- Product Family 180
- Multiple-Motor Branch 181
- Circuits and Motor 181
- Controllers Listed for Group 181
- Installation – General 181
- Maximum Fuse Ampere 183
- Rating According to 183
- 7.2.10.4(1) and 7.2.10.4(2) 183
- Explanatory Example 185
- 14 AWG14 AWG 186
- CIP Information 193
- CIP Explicit Connection 194
- Behavior 194
- CIP Object Requirements 194
- Identity Object 195
- Message Router 196
- Assembly Object 196
- I/O Assemblies 197
- Instance 100 198
- Instance 101 199
- Name Parameter Instance 200
- Instance 150 201
- Instance 152 201
- Instance 154 202
- Instance 156 202
- Connection Manager Object 203
- Class 1 Connections 204
- Class 3 Connections 205
- Discrete Input Point 206
- Discrete Output Point 206
- Appendix B CIP Information 208
- CIP Information Appendix B 209
- Analog Input Point Object 211
- Analog Output Point Object 211
- Parameter Object 212
- Parameter Group Object 213
- Discrete Input 214
- Group Object 214
- Discrete Output 214
- Control Supervisor Object 215
- Overload Object 216
- Device Level Ring (DLR) 217
- Extended Device Object 217
- DPI Fault Object 218
- DPI Alarm Object 222
- TCP/IP Interface Object 223
- Ethernet Link Object 224
- Trip and Warning 226
- Email Object 226
- Using DeviceLogix™ 229
- DeviceLogix Programming 230
- ➊ IPS Units 235
- ArmorStart LT 236
- Download the AOP 237
- ‘Next’ to continue 239
- Use of the AOP 242
- 1756-EN2TR and click OK 244
- Name Value Description 250
- Rockwell Automation Support 252
- Documentation Feedback 252
- Trademark List 252
Související produkty a manuály pro Zařízení Rockwell-automation 294E ArmorStart LT EtherNet/IP Version - User Manu
Zařízení Rockwell-automation 193-EE Bul 193 E1 PLUS Overload Relay Application Uživatelský manuál
(6 stránky)
(6 stránky)
Zařízení Rockwell-automation 440P Small Metal Safety Switches (4-Pin) Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 440P Bulletin 440P 2 N.C. Small Metal Safety Posit Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 150-SM6 SMC-50 Soft Starter Parameter Configuratio Uživatelský manuál
(6 stránky)
(6 stránky)
Zařízení Rockwell-automation 440R MSR178DP Minotaur Installation Instructions Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 802PR Type LA and Type XA, Series C Installation I Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 442L SafeZone Singlezone & Multizone Safety La Uživatelský manuál
(60 stránky)
(60 stránky)
Zařízení Rockwell-automation 21G PowerFlex 750-Series AC Drives Programming Man Uživatelský manuál
(544 stránky)
(544 stránky)
Zařízení Rockwell-automation 592-EEKF_EEMG E1 Plus Overload Relay Application a Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 150-SM3_SM4 SMC-50 Soft Starter I/O Option Module Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 284D- ArmorStart Base and Control Module Replaceme Uživatelský manuál
(2 stránky)
(2 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce