Rockwell-automation 20P PowerFlex DC Drive - Frame D Pulse Transformer Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Rockwell-automation 20P PowerFlex DC Drive - Frame D Pulse Transformer. Rockwell Automation 20P PowerFlex DC Drive - Frame D Pulse Transformer Circuit Board User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 8
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Publication 20P-IN050A-EN-P
PowerFlex® DC Drive
Frame D Pulse Transformer Circuit Board
Installation Instructions
What This Kit Includes
Pulse transformer circuit board
Six screws and washers
6 gate lead cables with connectors (for non-regenerative drives only)
12 gate lead cables with connectors (for regenerative drives only)
Static strap
Tools That You Need
Phillips
®
screwdriver
Hexalobular screwdriver
Nut driver or wrench
Phillips
®
is a registered trademark of Phillips Screw Company.
What You Need to Do
To install the switching power supply board:
Step 1: Remove power from the drive
Step 2: Remove the protective covers
Step 3: Remove the switching power supply board
Step 4: Remove the existing pulse transformer board
Step 5: Install the new pulse transformer board
Step 6: Install the switching power supply board
Step 7: Replace the protective covers and document the change
ATTENTION: Only qualified personnel familiar with DC drives
and associated machinery should plan or implement the installation,
start-up and subsequent maintenance of the system. Failure to comply
may result in personal injury and/or equipment damage.
ATTENTION: To avoid an electric shock hazard, ensure that all
power to the drive has been removed before performing the following.
ATTENTION: This drive contains ESD (Electrostatic Discharge)
sensitive parts and assemblies. Static control precautions are required
when installing, testing, servicing or repairing this assembly.
Component damage may result if ESD control procedures are not
followed. If you are not familiar with static control procedures,
reference A-B publication 8000-4.5.2, “Guarding Against
Electrostatic Damage” or any other applicable ESD protection
handbook.
Zobrazit stránku 0
1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Installation Instructions

Publication 20P-IN050A-EN-PPowerFlex® DC DriveFrame D Pulse Transformer Circuit BoardInstallation InstructionsWhat This Kit Includes• Pulse transforme

Strany 2 - Protective Covers

Publication 20P-IN050A-EN-P2Step 1: Remove Power from the Drive1. Remove and lock-out all incoming power to the drive. Step 2: Remove the Protective C

Strany 3 - Figure 1 Cover Removal

3Publication 20P-IN050A-EN-PFigure 1 Cover Removal 4. Disconnect the HIM communication cable from the connector on the upper right corner of the Con

Strany 4 - Switching Power Supply

Publication 20P-IN050A-EN-P4Step 3: Remove the Switching Power Supply Board1. Loosen the eight hexalobular screws that secure the protective plastic c

Strany 5 - Step 4: Remove the

5Publication 20P-IN050A-EN-PFigure 2 Switching Power Supply Circuit Board Layout Step 4: Remove the Existing Pulse Transformer Board1. Disconnect th

Strany 6 - (9…10.5 lb•in)

Publication 20P-IN050A-EN-P6Figure 3 Pulse Transformer Circuit Board Layout XUVXSWXSW1XCD_IOXUVWXCDXRXSPFS378 79 35 36 75 76 81 82 U2 V2X4

Strany 7 - Pulse Transformer Board

7Publication 20P-IN050A-EN-PStep 5: Install the New Pulse Transformer BoardInstall the new pulse transformer board in reverse order of removal as deta

Strany 8

Publication 20P-IN050A-EN-P - May 2010Copyright © 2010 Rockwell Automation. All rights reserved. Printed in USA.www.rockwellautomation.comAmericas: Ro

Komentáře k této Příručce

Žádné komentáře