Rockwell-automation 20P PowerFlex DC Drive - Frame A SCR Modules for D Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Rockwell-automation 20P PowerFlex DC Drive - Frame A SCR Modules for D. Rockwell Automation 20P PowerFlex DC Drive - Frame A SCR Modules for Drive w/Power Traces Circuit Board User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 18
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Installation Instructions
PowerFlex
®
DC Drive - Frame A SCR Modules
for Drives with a Power Traces Circuit Board
What This Kit Includes
SCR modules (3 for non-regenerative drives, 6 for regenerative drives)
Mounting screws and washers (6 for non-regenerative drives, 12 for
regenerative drives)
Gate leads (6 for non-regenerative drives, 12 for regenerative drives)
Thermal Grease
Static strap
Important:The SCR Modules supplied with this kit should only be used in
the following Frame A drives:
!
ATTENTION: Only qualified personnel familiar with DC
drives and associated machinery should plan or implement the
installation, start-up and subsequent maintenance of the system.
Failure to comply may result in personal injury and/or equipment
damage.
!
ATTENTION: To avoid an electric shock hazard, ensure that all
power to the drive has been removed before performing the
following.
!
ATTENTION: This drive contains ESD (Electrostatic
Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing or
repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with
static control procedures, reference A-B publication 8000-4.5.2,
“Guarding Against Electrostatic Damage” or any other
applicable ESD protection handbook.
230V AC Input 460V AC Input
Drive Current
Rating Code DC Amps
AC Line
Amps HP
Drive Current
Rating Code DC Amps
AC Line
Amps HP
7P0 7 5.7 1.5 4P1 4.1 3.3 2
9P0 9 7.4 2 6P0 6 4.9 3
012 12 9.8 3 010 10 8.2 5
020 20 16 5 014 14 11.4 7.5
029 29 24 7.5 019 19 15.5 10
038 38 31 10 027 27 22.1 15
055 55 45 15 035 35 28.6 20
045 45 36.8 25
052 52 42.5 30
Zobrazit stránku 0
1 2 3 4 5 6 ... 17 18

Shrnutí obsahu

Strany 1 - PowerFlex

Installation InstructionsPowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board What This Kit Includes• SCR modules (

Strany 2 - What You Need to Do

10 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board Figure 1 Pulse Transformer Circuit Board Layout XP11XSW1X3

Strany 3 - Protective Covers

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 11 2. Remove the plug-in control power terminal block from the

Strany 4 - 1.5 N•m (13.3 lb•in)

12 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 6. Remove the appropriate gate leads (refer to Figure 1 on p

Strany 5 - Pull tabs out

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 13 8. Remove the six screws that secure the Pulse Transformer b

Strany 6 - Control Board

14 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board Step 5: Remove the Power Traces Board1. Remove the screws th

Strany 7

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 15 3. Remove all screws and washers that secure the board to th

Strany 8 - Power Supply Boards

16 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board Step 6: Remove the Existing SCR Modules1. Remove the two scr

Strany 9 - Remove screw

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 17 Step 8: Install the Power Traces BoardInstall the Power Trac

Strany 10 - FIR1-XX rev. “Q” and higher

Publication 20P-IN020B-EN-P - December 2009Supersedes 20P-IN020A-EN-P - March 2009 Copyright © 2009 Rockwell Automation. All rights reserved. Printed

Strany 11

2 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board Tools That You Need• Phillips® screwdriver• Flathead screwdri

Strany 12

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 3 Step 1: Remove Power from the Drive1. Remove and lock-out all

Strany 13 - Regenerative drive shown

4 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 2. Disconnect the DPI cable from the HIM assembly (if present

Strany 14 - Traces Board

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 5 6. Disconnect the HIM Communication cable from the connector

Strany 15 - Traces board from the drive

6 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board Step 3: Remove the Control EMI Shield and Control BoardNote:

Strany 16 - Step 6: Remove the

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 7 3. Remove the four screws (and ground wire on the lower left

Strany 17

8 PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board Step 4: Remove the Pulse Transformer and Switching Power Supp

Strany 18 - Related Documentation

PowerFlex® DC Drive - Frame A SCR Modules for Drives with a Power Traces Circuit Board 9 – For all other drives, remove the two screws that secure the

Komentáře k této Příručce

Žádné komentáře