Rockwell-automation 20L PowerFlex 700L Frame 2 DC Bus Bar Conversion K Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Rockwell-automation 20L PowerFlex 700L Frame 2 DC Bus Bar Conversion K. Rockwell Automation 20L PowerFlex 700L Frame 2 DC Bus Bar Conversion Kit User Manual Uživatelská příručka

Installation Instructions

PowerFlex

700L Frame 2 DC Bus Bar

Conversion Kit SK-L1-DCBS1-F2

Where This Kit Is Used

This kit is used to provide electrical connection points to the DC bus of a

PowerFlex 700L Frame 2 drive.

What This Kit Includes

• DC- bus bar and hardware

• DC+ bus bar and hardware

• Flat dielectric support

• Angle dielectric bus bar supports and hardware

• Torque Seal

Tools That You Need

• Phillips

screwdriver (#2)

• Standard flat tip screwdriver

• Torque wrench

Phillips

is a registered trademarks of Phillips Screw Company.

ATTENTION: To avoid an electric shock hazard, ensure that all

power to the drive has been removed before performing any steps

of these instructions.

ATTENTION: To avoid an electric shock hazard, verify that the

voltage on the bus capacitors has completely discharged before

performing any work on the drive. After removing power to the

drive, wait 5 minutes for the bus capacitors to discharge. Remove

the front cover of the drive. Measure the DC bus voltage at the

DC+ TESTPOINT and DC- TESTPOINT sockets on the front of

the drive (see drawing in Step 1.4). The voltage must be zero.

ATTENTION: HOT surfaces can cause severe burns. Do not

touch the heatsink surface during operation of the drive. After

disconnecting power allow time for cooling.

ATTENTION: This drive contains ESD (Electrostatic

Discharge) sensitive parts and assemblies. Static control

precautions are required when installing, testing, servicing or

repairing this assembly. Component damage may result if ESD

control procedures are not followed. If you are not familiar with

static control procedures, refer to Allen-Bradley publication

8000-4.5.2, “Guarding Against Electrostatic Damage” or any

other applicable ESD protection handbook.

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Conversion Kit SK-L1-DCBS1-F2

Installation InstructionsPowerFlex® 700L Frame 2 DC Bus Bar Conversion Kit SK-L1-DCBS1-F2Where This Kit Is UsedThis kit is used to provide electric

Strany 2 - Step 1: Removing Power

2 PowerFlex® 700L Frame 2 DC Bus Bar Conversion Kit SK-L1-DCBS1-F2 What You Need to DoTo install the PowerFlex® 700L Frame 2 Power Module DC Bus Bar

Strany 3 - Section A-A

PowerFlex® 700L Frame 2 DC Bus Bar Conversion Kit SK-L1-DCBS1-F2 3 4. Measure the DC bus voltage at the DC+ TESTPOINT and DC- TESTPOINT sockets on t

Strany 4 - Cassette, and Vent Cover

4 PowerFlex® 700L Frame 2 DC Bus Bar Conversion Kit SK-L1-DCBS1-F2 Step 2: Removing the Drive Cover, Inverter Cassette, and Vent Cover1. Remove the

Strany 5 - DC+ Bus Bar

PowerFlex® 700L Frame 2 DC Bus Bar Conversion Kit SK-L1-DCBS1-F2 5 4. Locate the two (2) screws with ring lugs on the laminated bus bar, and remove

Strany 6 - Step 3: Assembling the Kit

6 PowerFlex® 700L Frame 2 DC Bus Bar Conversion Kit SK-L1-DCBS1-F2 Step 3: Assembling the Kit Parts1. Assemble the DC- bus bar to the drive using th

Strany 7 - (Cover Removed)

PowerFlex® 700L Frame 2 DC Bus Bar Conversion Kit SK-L1-DCBS1-F2 7 3. Assemble the flat dielectric support to the top of the drive. Align the flat d

Strany 8

www.rockwellautomation.comAmericas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 4

Komentáře k této Příručce

Žádné komentáře

Rockwell-automation 20L PowerFlex 700L Frame 2 DC Bus Bar Conversion K Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Rockwell-automation 20L PowerFlex 700L Frame 2 DC Bus Bar Conversion K. Rockwell Automation 20L PowerFlex 700L Frame 2 DC Bus Bar Conversion Kit User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Zařízení Rockwell-automation 20L PowerFlex 700L Frame 2 DC Bus Bar Conversion K