Rockwell-automation 20D-MDI-C1 Multi-Device Interface Option Board for Uživatelský manuál stáhnout pdf

Installation Instructions

Multi-Device Interface Option Board for

PowerFlex® 700S Drives

What This Kit Contains

Verify that your kit contains the items listed in the following table. If your

kit does not contain the correct items, contact your Rockwell Automation

sales representative.

ATTENTION: To avoid an electric shock hazard, ensure that

all power to the drive has been removed before performing the

following.

ATTENTION: To avoid an electric shock hazard, verify that

the voltage on the bus capacitors has discharged before

performing any work on the drive. Measure the DC bus voltage

at the DC+ & DC- terminals. The voltage must be zero.

ATTENTION: HOT surfaces can cause severe burns. Do not

touch the heatsink surface during operation of the drive. After

disconnecting power allow time for cooling.

ATTENTION: This drive contains ESD (Electrostatic

Discharge) sensitive parts and assemblies. Static control

precautions are required when installing, testing, servicing or

repairing this assembly. Component damage may result if ESD

control procedures are not followed. If you are not familiar with

static control procedures, reference A-B publication 8000-4.5.2,

“Guarding Against Electrostatic Damage” or any other

applicable ESD protection handbook.

ATTENTION: Hazard of permanent eye damage exists when

using optical transmission equipment. This product emits intense

light and invisible radiation. Do not look into SynchLink

fiber-optic ports or SynchLink fiber-optic cable connectors.

ATTENTION: The sheet metal cover and mounting screws on

the ASIC Board located on the power structure are energized at

(-) DC bus potential high voltage. Risk of electrical shock,

injury, or death exists if someone comes in contact with the

assembly.

Quantity: Description

1 MDI Option circuit board

2 “Stacker” connectors

1Screw

3 Stand-offs

1 2 3 4 5 6 ... 19 20

Shrnutí obsahu

Strany 1 - PowerFlex® 700S Drives

Installation InstructionsMulti-Device Interface Option Board for PowerFlex® 700S Drives What This Kit ContainsVerify that your kit contains the items

Strany 2 - Step 1: Remove Power

10 Multi-Device Interface Option Board for PowerFlex® 700S Drives Step 8: Wire the MDI Option BoardTerminal block P1 contains connection points for a

Strany 3 - Step 2: Remove the Drive

Multi-Device Interface Option Board for PowerFlex® 700S Drives 11 Recommended CablesIf you are using this motor and feedback device: Use this cable: S

Strany 4 - Frame 10 - 13 Size Drives

12 Multi-Device Interface Option Board for PowerFlex® 700S Drives Figure 2 Rotary Encoder connections for MPL-A5xx and MPL-Bxxx motors or 1326AB-BXX

Strany 5 - Phase I Drive (if necessary)

Multi-Device Interface Option Board for PowerFlex® 700S Drives 13 Figure 5 Rotary Encoder connections for MPL-A3xx - MPL-A45xx and all MPG series mo

Strany 6 - II Control Cassette Covers

14 Multi-Device Interface Option Board for PowerFlex® 700S Drives Figure 8 Rotary Encoder connections with Stegmann shielded twisted-pair cable and

Strany 7 - Existing MDI Option Board

Multi-Device Interface Option Board for PowerFlex® 700S Drives 15 Step 9: Install the Phase II Control Cassette CoversIn order to install the Phase II

Strany 8 - Step 6: Install the New MDI

16 Multi-Device Interface Option Board for PowerFlex® 700S Drives Install the Phase II Control Cassette Frame 9 - 13 Size Drives Task DescriptionSlide

Strany 9 - (if removed in Step 3)

Multi-Device Interface Option Board for PowerFlex® 700S Drives 17 Step 10: Document the ChangeDocument the installation of the MDI option board on the

Strany 10 - Option Board

18 Multi-Device Interface Option Board for PowerFlex® 700S Drives Step 11: Install the Drive Cover(s)Phase I Drives Frames 1 - 6 The procedure for ins

Strany 11 - Recommended Cables

Multi-Device Interface Option Board for PowerFlex® 700S Drives 19 Supported Linear SensorsImportant:Only one Linear Sensor can be installed at a time.

Strany 12 - Connection Examples

2 Multi-Device Interface Option Board for PowerFlex® 700S Drives Tools That You Need• Phillips® screwdriver for M3 screws• POZIDRIV® screwdriver for M

Strany 13

Strany 14

Multi-Device Interface Option Board for PowerFlex® 700S Drives 3 Step 2: Remove the Drive Cover(s) Frame 1 - 6 Size DrivesEsc7 8 94 5 61 2 3.0 +/-SelJ

Strany 15 - Control Cassette Covers

4 Multi-Device Interface Option Board for PowerFlex® 700S Drives Frame 9 Size DrivesFrame 10 - 13 Size DrivesOpen the door of the drive enclosure cont

Strany 16 - Frame 1 - 6 Size Drives

Multi-Device Interface Option Board for PowerFlex® 700S Drives 5 Step 3: Remove the Control Assembly from Phase I Drive (if necessary)This step is nec

Strany 17 - Step 10: Document the

6 Multi-Device Interface Option Board for PowerFlex® 700S Drives Step 4: Remove the Phase II Control Cassette CoversIt is necessary to remove the cass

Strany 18 - Specifications

Multi-Device Interface Option Board for PowerFlex® 700S Drives 7 Remove the Phase II Cassette Covers (All Drive Sizes) Step 5: Remove the Existing MDI

Strany 19 - Supported Rotary Encoders

8 Multi-Device Interface Option Board for PowerFlex® 700S Drives Step 6: Install the New MDI Option BoardPhase I DrivesImportant:Do not use a screwdri

Strany 20

Multi-Device Interface Option Board for PowerFlex® 700S Drives 9 Phase II DrivesImportant:Do not use a screwdriver to pry the P1 terminal block from t