Rockwell-automation 20-COMM-M Modbus/TCP Adapter Uživatelský manuál Strana 21
- Strana / 98
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Installing the Adapter 2-7
20-COMM-M Modbus/TCP Adapter User Manual
Publication 20COMM-UM014C-EN-P
Figure 2.5 Drive and Adapter Status Indicators (location on drive may vary)
Table 2.A Drive and Adapter Start-Up Status Indications
Item Name Color State Description
Drive STS Indicator
➊
STS
(Status)
Green Flashing Drive ready but not running, and no faults are present.
Steady Drive running, no faults are present.
Yellow Flashing,
Drive Stopped
An inhibit condition exists – the drive cannot be
started. Check drive Parameter 214 - [Start Inhibits].
Flashing,
Drive Running
An intermittent type 1 alarm condition is occurring.
Check drive Parameter 211 - [Drive Alarm 1].
Steady,
Drive Running
A continuous type 1 alarm condition exists. Check
drive Parameter 211 - [Drive Alarm 1].
Red Flashing A fault has occurred.
Steady A non-resettable fault has occurred.
Adapter Status Indicators
➋
PORT Green Flashing Normal Operation. The adapter is establishing an I/O
connection to the drive. It will turn steady green or red.
Steady Normal Operation. The adapter is properly connected
and communicating with the drive.
MOD Green Flashing Normal Operation. The adapter is operating but is not
transferring I/O data to a controller.
Steady Normal Operation. The adapter is operating and
transferring I/O data to a controller.
NET A Green Off BOOTP is enabled or a valid IP address is not set.
Flashing Normal Operation. The adapter is properly connected,
has an IP address, and is connected to a Modbus/TCP
network but does not have an I/O connection.
Steady Normal Operation. The adapter is properly connected
and communicating on the network to a controller.
NET B Green Off Normal Operation. The adapter is properly connected
but is idle.
Flashing Normal Operation. The adapter is properly connected,
BOOTP is enabled, and the adapter is transmitting
data packets on the network.
➋
➊
PORT
MOD
STS
NET A
NET B
- 20-COMM-M Modbus/TCP Adapter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 7
- Rockwell Automation 8
- Conventions Used in This 8
- Getting Started 9
- Features 10
- Compatible Products 10
- Required Equipment 11
- Safety Precautions 11
- 1-4 Getting Started 12
- Quick Start 13
- Status Indicators 14
- Installing the Adapter 15
- Setting the Web Pages 16
- Connecting the Adapter to 17
- Applying Power 20
- Commissioning the Adapter 22
- Configuring the Adapter 23
- Using the PowerFlex 7-Class 24
- Using BOOTP 25
- Configuring the Adapter 3-5 27
- Setting the IP Address 28
- Subnet Mask, and Gateway 28
- Setting the Data Rate 30
- Setting the I/O 30
- Configuration 30
- Setting a Communication 31
- Fault Action 31
- Setting the Message I/O 32
- Setting Web Access Control 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Flash Updating the Adapter 35
- 3-14 Configuring the Adapter 36
- Chapter 4 37
- Unit Identifier (Port Number) 38
- Using the I/O 39
- Par. 82 - [Maximum Speed] 42
- Accessing Device Parameters 45
- Direct Access Method 45
- Indirect Access Method 46
- Using Datalinks 48
- Rules for Using Datalinks 48
- Reading Datalinks 48
- Writing Datalinks 49
- Conversion Example: 50
- Supported Modbus 51
- Registers 51
- Chapter 5 53
- PORT Status Indicator 54
- MOD Status Indicator 54
- NET A Status Indicator 55
- NET B Status Indicator 55
- Viewing Adapter Diagnostic 56
- Viewing and Clearing 58
- Table 5.B Adapter Events 59
- 5-8 Troubleshooting 60
- Chapter 6 61
- Process Display Pop-up 64
- TCP/IP Configuration Web 65
- Configure E-mail 66
- Notification Web Page 66
- DPI Device Information 69
- Kit (20-XCOMM-DC-BASE) 73
- Specifications 75
- Environmental 76
- Regulatory Compliance 76
- Adapter Parameters 77
- B-6 Adapter Parameters 82
- Logic Command/Status Words 83
- Logic Status Word 84
- PowerFlex 700S Drives 85
- Glossary 87
- G-2 Glossary 88
- F Fault Action 89
- G Gateway 89
- H Hardware Address 89
- I I/O Data 90
- L Logic Command/Logic Status 91
- M Modbus/TCP Network 91
- N NVS (Non-Volatile Storage) 91
- R Reference/Feedback 92
- S Status Indicators 92
- Z Zero Data 92
- May, 2010 98
Související produkty a manuály pro Zařízení Rockwell-automation 20-COMM-M Modbus/TCP Adapter
Zařízení Rockwell-automation 140EX-JE2_JE3 Molded Case Circuit Breaker Uživatelský manuál
(2 stránky)
(2 stránky)
Zařízení Rockwell-automation 140G-R-EA1TA Electrical Signalling of Overcurrent Uživatelský manuál
(3 stránky)
(3 stránky)
Zařízení Rockwell-automation 56AMXN ControlLogix/AutoMax/Communication/Module Uživatelský manuál
(24 stránky)
(24 stránky)
Zařízení Rockwell-automation 140G-K-EAM1A Early Make Aux Contact for Rotary Han Uživatelský manuál
(3 stránky)
(3 stránky)
Zařízení Rockwell-automation 57RF RFID ICODE Handheld Interface User Manual Uživatelský manuál
(112 stránky)
(112 stránky)
Zařízení Rockwell-automation 20-COMM PowerFlex 7-Class DPI (Drive Peripheral In Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 20P PowerFlex DC Drive - Frame D, Series B Fan Cir Uživatelský manuál
(6 stránky)
(6 stránky)
Zařízení Rockwell-automation 22-HIM-C2S PowerFlex 4-Class Remote Small HIM Uživatelský manuál
(4 stránky)
(4 stránky)
Zařízení Rockwell-automation 20P PowerFlex DC Drive - Frame D Field Dual Diode Uživatelský manuál
(8 stránky)
(8 stránky)
Zařízení Rockwell-automation 22B PowerFlex 40 Custom Firmware Inst. - Option AF Uživatelský manuál
(4 stránky)
(4 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce