Rockwell-automation 140G-Nx_NSx LSI Getting Started Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Rockwell-automation 140G-Nx_NSx LSI Getting Started. Rockwell Automation 140G-Nx_NSx LSI Getting Started Benutzerhandbuch Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 6
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
I
In
=
1600A
2
1
2
1
LSI Getting started for 140G-N, 140G-NS
LSI Getting started
LSI Erste Schritte
LSI Guide de démarrage
LSI Getting started
Bul. 140G
DIR 1000591R0001 (L3554)
WARNING:
WARNUNG:
AVERTISSEMENT:
To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
140G-N
140G-NS
140G-N_, 140G-NS_
LSI
Zobrazit stránku 0
1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - Bul. 140G

IIn=1600A2121LSI Getting started for 140G-N, 140G-NSLSI Getting startedLSI Erste SchritteLSI Guide de démarrageLSI Getting startedBul. 140GDIR 1000591

Strany 2

123Warning-Attenzione-Achtung-Attention-AtenciónPlease read all documentation before making changes to the circuit breaker settings. After setting the

Strany 3 - (t=k/If

IIn =1000AtI2t2SItI2t2SI0,25s0,25s10000A(10xIn)Protection LProtezione LSchutzfunktion L Protection L Protección LProtection SProtezione SSchutzfunkti

Strany 4 - In=1000A

Protection IProtezione ISchutzfunktion I Protection IProtección IExample-Esempio-Beispiel-Exemple-Ejemplo In=1000A

Strany 5 - Señalizaciones LED

LED 1 LED 2 LED 3 LED 4L prealarmL alarmS alarmONL tripS tripI tripONONON(*)=Iu=1200A;In=1000A;InN=200%Example-Esempio-Beispiel-Exemple-EjemploNO!!OK!

Strany 6 - Final check

10Trip test Trip test Auslöseprüfung Test de déclenchement Test de disparoSettaggi di defaultStandardeinstellungenRéglages par défautConfiguraciones p

Komentáře k této Příručce

Žádné komentáře